Clint's Hybrid

[Brush Ape]

"Boof" haha. We had, "Gizmo." He called in bomb threats from the nurses office so we could go shoot baskets at the Jr. High gym for a couple hours.

 

[Keith Gandy]

One of the best balancing rigs ive picked up is Johns 661r with a Stihl 32 es light

On the 241's are you pulling the jug and carb assembly off in one piece?

I dont. I loosen the ignition and the self tappers in the bottom of the airfilter housing and pull it off the intake manifold and the cylinder and manifold comes off with 4 bolts

 

[foragefarmer]

One of the best balancing rigs ive picked up is Johns 661r with a Stihl 32 es lightView attachment 4478

I dont. I loosen the ignition and the self tappers in the bottom of the airfilter housing and pull it off the intake manifold and the cylinder and manifold comes off with 4 bolts

Hmmm, can't tell from your description if we are doing the same thing or not and I have no photos handy.

I remove the muffler, remove cylinder bolts, disconnect electrical to carb, remove trigger linkage, remove bolts in tray under carb, pop the rubber buffers off the carb manifold and push the two retainer tabs holding the tray in and the jug, manifold, carb, tray comes out in one assembly and then disconnect the fuel line.

 

[foragefarmer]

Oops forgot remove spark plug and spring av.

Take the screws out. And remove the rubber tabs.



Then pop the retainer tabs I am pointing to in the next pic.



On both sides and everything comes out.

 

[Keith Gandy]

Hmmm, can't tell from your description if we are doing the same thing or not and I have no photos handy.

I remove the muffler, remove cylinder bolts, disconnect electrical to carb, remove trigger linkage, remove bolts in tray under carb, pop the rubber buffers off the carb manifold and push the two retainer tabs holding the tray in and the jug, manifold, carb, tray comes out in one assembly and then disconnect the fuel line.

Ya that sounds like what I do except I pull the whole rear assembly loose from the manifold. If u dont u must be using a right angle t27 to dissconnect the manifold from the cylinder if the carb isnt removed first?

 

[foragefarmer]

I'll do that if I need to but the last time I had it apart was for new rings and I just swapped the rings and put everything back together didn't even disconnect the fuel line.

 

[Keith Gandy]

I'll do that if I need to but the last time I had it apart was for new rings and I just swapped the rings and put everything back together didn't even disconnect the fuel line.

Ok gotcha. Ill usually need the manifold off to do alil porting so I split the front and back half and when I unbolt the cylinder the manifold stays with it and it just move the back half to the side and go to work

 

[Keith Gandy]

I'll do that if I need to but the last time I had it apart was for new rings and I just swapped the rings and put everything back together didn't even disconnect the fuel line.

Is the 441c the same type setup?

 

[Keith Gandy]

View attachment 4496

Oops forgot remove spark plug and spring av.

Take the screws out. And remove the rubber tabs.

View attachment 4497

Then pop the retainer tabs I am pointing to in the next pic.

View attachment 4498

On both sides and everything comes out.

Man that rubber snap tab on the right side is a pain!!!! Lol!!

 

[foragefarmer]

Is the 441c the same type setup?

Never owned one.

 

[Deets066]

You might be onto something......but would it lose that racy feel? It's bad ass was a 24" bar.

I'm gunna go back into mine Randy, it's gunna get a small half circle ground in the intake skirt of the piston and a hefty set of fingers. I bet it picks up more of that "racey" feel. I'll do before and after vids.

 

[jmssaws]

I like big wide fingers they seem to make the most power

 

[Moparmyway]

I like big wide fingers they seem to make the most power

Be interesting to see if big fingers help the hybrid get more grunt !!

 

[jmssaws]

Be interesting to see if big fingers help the hybrid get more grunt !!

I'm thinking that everything below the piston was enlarged it would gain case capacity and perhaps grunt. Just a theory though.

 

[Moparmyway]

I'm thinking that everything below the piston was enlarged it would gain case capacity and perhaps grunt. Just a theory though.

We'll see how Keiths runs after he puts them in !!

I think it will run stronger

 

[jmssaws]

If it needs more capacity then it's easy to get.

I've not ground on my hybrid yet so I'm waiting on deets to find the power. Lol

 

[jmssaws]

I think a big ole set of fingers will put some grunt in one.

 

[huskihl]

I like big wide fingers they seem to make the most power

That's what she said

 

[Brush Ape]

One time I left Mike Brown in my '74 Power Wagon to sleep while I was in a friends house. We got carried away talking in there and I come out, All I see sticking out of my driver's side seat was a German Shorthaired Pointer's head. He made a slit and dug out the foam and got inside the slit so he could fart and share it with me later good boy thanks Mike.

For illustrative purpose.... from fellow member Illinois boy jrsdws' post:

If he's from up around Morrisonville as sharp as that pooch looks, could be Mike Brown's cuz......

 

[Brush Ape]

@jrsdws