Another chainsaw dyno...

[mdavlee]

Whenever you are ready.

Sure hope this Printer works as a backup. If the software shows up I will be able to use the laptop and a regular printer.





I have heard those are flat nasty... can be hard on recoils if you don't know how to start them though

I built one for Walt up in the mountains of Arizona that busted a recoil at my house. It was 235 or so there with no break in and 185 at his elevation.

 

[Red97]

I built one for Walt up in the mountains of Arizona that busted a recoil at my house. It was 235 or so there with no break in and 185 at his elevation.

Them darn recoils maybe a kick start would be better.

 

[mdavlee]

Them darn recoils maybe a kick stsrt would be better.

That would be easier or an electric start on a drill

 

[Red97]

Well the printer prints, but dosent seem to communicate with my readout box...

Matched all the settings according to the manual. Sure hope it's just th printer.


Software did show up, have to wait for the correct cable for that. Sure hope I can get the software working.


This is a whole new level of control.

 

[Red97]

It even makes engine noises...



Playing with the demo runs.

 

[ayoungtexan]

It even makes engine noises...

View attachment 241025

Playing with the demo runs.

It makes engine noises! Me likey.

 

[TreeLife]

I’m curious to see the numbers now. I need to get around to shopping that 2188 to you

Would you consider...sailing that 2188?

 

[Evansaw]

Hi, i would like to see how a hotsaw on methanol and nitro and pipe performs.like a 088.

if it wasn't across Atlantic I could send one

 

[Deets066]

Software did show up, have to wait for the correct cable for that. Sure hope I can get the software working.
View attachment 241016

This is a whole new level of control.

Hopefully your software reads above 15,000 if I send ya any saws. Lol

 

[Red97]

Hopefully your software reads above 15,000 if I send ya any saws. Lol

Pretty sure it will read as fast as you want lol

Well prolly only 99,000 rpm

 

[Terry Syd]

Hopefully your software reads above 15,000 if I send ya any saws. Lol

Crikey, I read that and thought, Illinois doesn't have any high mountains...

 

[jk14]

026,260 are stock, and the 260 will prolly get ported.

044 is dual port and squish set ex raised widen light mods.

046 is stock, maybe a dual port.

066 is dual port, maybe big bore? Supposed to be a runner.

395 is the first one I ported. Squish set, band cut normal numbers etc..

May post some of the numbers.

Whatcha running for fuel/oil mix for your dyno runs? If you don't mind me asking.

 

[Red97]

Whatcha running for fuel/oil mix for your dyno runs? If you don't mind me asking.

Heavy 40:1 with amsoil dominator.

 

[mdavlee]

Would you consider...sailing that 2188?

Everything I got is for sale for the right price[emoji23]

 

[Deets066]

Crikey, I read that and thought, Illinois doesn't have any high mountains...

No, we sure don’t. Lol

 

[Red97]

Hooray big saws.

 

[CR888]

A thermocouple plug washer recording cylinder temps would add to the dyno's box of tricks. Keeping saws in the safe zone and also used as a tuning aid.

 

[Red97]

A thermocouple plug washer recording cylinder temps would add to the dyno's box of tricks. Keeping saws in the safe zone and also used as a tuning aid.

I have the channels for that along with 4 more thermocouple. and about 10 other options that I don't have the slightest clue about.

Fully optioned harness.

Baby steps

Baby steps

Need to get the software hooked up next. Then learn to use that.

 

[Stevetheboatguy]

How much can you raise the oil pressure on a 088 for a 59" bar?



Joes saw porting, dyno tuning and extreme oil pump modification services.

Too long a name ????? Ehh

Steven

 

[ayoungtexan]

View attachment 241474



How much can you raise the oil pressure on a 088 for a 59" bar?



Joes saw porting, dyno tuning and extreme oil pump modification services.

Too long a name ????? Ehh

Steven

Solve that oil output with a 395. A 395 cures cancer