064, 066 MS650, MS660 info thread

[Woodwackr]

I have jugs, have to see what’s in my box of 064/066 covers

Need an early 54mm..or 2. I have plenty of 52s

 

[Woodwackr]

Got case halves matched up today, 9 cases. Still need to go over them in detail, looking for stripped bolt holes, cracks, etc. I’ll make what repairs I can do and throw the rest as is on eBay.
sorted all the smaller parts, including screws…sheesh…what a pain trying to read the tops
12.9 and 10.x. If I couldn’t read it under magnification it became a 10, lol.

 

[ManiacalMark]

Need an early 54mm..or 2. I have plenty of 52s

I’ll take a look, I know I have two non decomp thick base mahle.

 

[markds2]

Just heard this week that the 9640 003 1850 Oil seal 17x32.9x3.6 (PTO side crank seal for 064, 066 and MS660) is NLA on its own from Stihl. It is, however, still available as part of the full set of gaskets and seals, part number 1122 007 1053. Apparenetly as the MS660 has been out of production for over 10 years now parts are starting to become obsolete. My dealer also mentioned that the back handle/tank assy for the MS660 is also NLA.

 

[PogoInTheWoods]

I would suspect a certain level of inventory still exists among domestic US suppliers considering the number of units sold and still in professional use in the States.

Worst case, AM replacements are readily available.

 

[qurotro]

Just heard this week that the 9640 003 1850 Oil seal 17x32.9x3.6 (PTO side crank seal for 064, 066 and MS660) is NLA on its own from Stihl. It is, however, still available as part of the full set of gaskets and seals, part number 1122 007 1053. Apparenetly as the MS660 has been out of production for over 10 years now parts are starting to become obsolete. My dealer also mentioned that the back handle/tank assy for the MS660 is also NLA.

I believe the MS661 use the same PTO side seal. Probably Stihl got supply issues.

 

[markds2]

I believe the MS661 use the same PTO side seal. Probably Stihl got supply issues.

You are dead right, I have asked my dealer if it is temporary supply issue or permanent

 

[markds2]

I believe the MS661 use the same PTO side seal. Probably Stihl got supply issues.

Dealer has just emailed and said the 9640 003 1850 Oil seal now supercedes to the 9640 003 1851 oil seal on the NZ Spec 661C (MS661 C-M-Z). Same dimensions so no reason why it wont work on the 1122 series. He has no idea why it doesn't automatically supercede in the system on the 1122 parts lists.

 

[PogoInTheWoods]

I believe the MS661 use the same PTO side seal.

Indeed it does. My initial lookup for the part number was from MediaCAT which obviously didn't include the 661 in 2012. A quick check of my MS661 IPL shows the same part number.

 

[jmester]

I knew the day would come when we would be having these conversations. Sad day for sure. I feel that the 1122 series saws were some of the best saws ever made.

I have been stocking up on parts for a while. There is still a fair amount of supply. There is even some heated handle stuff if that is what you are into.

 

[jmester]

The flywheel side seal has changed also from 9640 003 1560 to 9640 003 1561.

 

[BrokenAgain]

Hey everyone. I just picked up a well used 066 that seams to run good but is missing a few parts and has a very wet muffler. Trying to id what year or anything about it so I get the correct parts. Thinking of getting a new OEM cylinder kit while they are still available. S/N is 133643975. The PO said they had a Stihl dealer put new bearings/seals in it but it doesn't really look like the case was split.

I really only wanted a 70cc saw but everyone is asking almost new prices around me