stihl

Hey Guys - I'm looking for one of the thick old-school 066 starters. I'm heading into another old 066 rebuild and have everything but the starter. I have literally tons of parts to trade or cash. Thanks!

Saw started as a JMS saw. Was lucky enough that Al agreed to go through it. At the time he had to tig the flywheel side exhaust bolt hole and retap as it had been stripped. It has came loose once but it’s held fine for quite awhile now. Saw now has a 044 Zama carb. Choke setup isn’t as smooth as...

Stihl Ms 440 arctic , replaced impulse line , intake boot , fuel line and diaphragms. When I put the saw back together and fired it up without the carb cover or air filter on( snugged the nuts down on the cover plate over the heater element) I noticed the element got very hot and...

Hey Guys - This is a long shot I know - I'm looking for one of the old 064 or 066 brake handles for the straight 3/4 wrap handle. The 064 part number I believe is 1122 792 9105, and the 066 one is 1122 792 9106. I have tons of stuff to trade and cash. Thanks!

Hey Guys- I'm putting my 661 up for trade or sale. It's a 100% stock saw that I bought as a project (off Ebay) that had been run over. The seller told me it had 10-12 hours on it, and I tend to believe that as there was no carbon build-up at all on the piston and very little in the cylinder...

I have done quite a few ms660 clone builds and I'm interested in learning how to do my own port work. I just started messing with squish and that seems to be going well. Next step is porting and timing. If anyone has any helpful tips or an already ported cylinder that I could purchase to use as...

Wondering if it would be possible. I am not so techy but i figure it would have to be a 661 coil and carb with a suitable flywheel(if there is one)? I am not interested in the 'would it be better' debate, just if it is possible.

Noticed there were a couple of chips out of one of the slots on the rim sprocket on my ms261 along with the chain getting tight and going slack (hanging about 1/4 inch off the bar) as I would pull the chain around by hand. At first I thought the rim sprocket was defective but the problem...

This may be a little off topic, but since this website gave me such great results when I needed chainsaw help, I figured I’d give this a go. I recently just came into ownership of a Stihl HS 45 hedge trimmer. It’s old and hasn’t been ran in a few years, but it’s got compression and is in...

Just wondering what your experiences of the 461 are, there are still a few new ones to be had, I like the non mt saws, are the AV numbers good on these saws. Do they balance well with the 25 inch factory bar they come with, how do they oil that bar, how much bigger could they pull and oil. I...

Up for sale is a nice running Stihl 028 Super for parts or repair that I am selling for a friend that used it for light firewood cutting. Saw looks to have been maintained by the looks of filters, sprocket etc.. Best I can tell has the original P&C. Has AM fuel caps and a small crack in the...

I bought this directly from Randy. It only has 1 tank through it. $800 shipped ConUS PayPal F/F or add 3% USPS m/o email or pm Mkf350@gmail.com

I bought this off another member here thinking I would use my current 3/4 wrap 661 for dedicated chainsaw mill but that didn’t happen. This one has been sitting on my shelf after I ran 1 tank through it right after I got it. Email or pm me. Mkf350@gmail.com $1300 shipped ConUS PayPal F/F or...

As an addendum to the other build threads on the MS462 this thread will cover cutting the cylinder base, as there really isn't that much different that I can add. Randandalino @Mastermind asked if I would do one, so here it is. He has a build thread about this model as well as @tree monkey ...

So, a couple of days ago, I decided to let my brother have my Stihl 038 Super. He had taken his two saw that he had over to one of his friends, who is a small engine mechanic.....apparently he has been waiting on the two saws to get fixed and they haven't come back....well over 4 to 6 months...

I’m looking for the following parts for a Poly flywheel 660: PTO side case 1/2 Tank handle Air cleaner / carb post Possibly a coil Please let me know what you have. I’d be happy to do some trading.

Went On lunch break and this sat out at a sale ! So I bought it !.. getting closer to a mill saw I've been looking for!

Looking for a bar for my 084. Figured I'd ask here before I bit the bullet and bought new. Willing to pay the right price for a nice used bar Thanks, Hank

Wanting a new OEM piston and cylinder kit for a stihl MS440 and one for Stihl MS460. Thanks

I'm looking for a more Eastern double dog setup for my 044, I still want double and preferably a roller chain catch but I just don't need big massive west coast spikes shortening my usable bar length. I had seen a few people say that the old 064 spikes were a good compromise and I've found some...