stihl

I bought a 16" Oregon Speedcut narrow kerf bar (160TXLGD025) for my Stihl 034, along with some Stihl 23RSP chain that I finally found. But mounting it doesn't work because the bar doesn't secure correctly even with the nuts fully tightened. The narrow bar leaves enough slop that it wobbles...

Good morning Men - I'm looking for some 661 parts and thought I'd try here before I buy from Evilbay or the general interwebs. I need a muffler and starter, both complete. I can also use a Max-Flow kit if someone has an extra. I have a lot to trade - Stihl, Husqvarna, Jonsered, McCulloch...

Kind of a wrap on these as stocks are dried/ing up, so here's a build thread on the World's last ported new 461. Tear down is pretty basic as well as covered before, a place to start nonetheless.

Hey folks. Hope you are well. I have a question, but first, a small amount of info on where I'm at... Recently, I purchased an Alaskan Sawmill (36") and a 462 for milling my own lumber. I didn't want to shell out the cash for a bandsaw sawmill, especially seeing how many are on backorder for...

KM90R-Z 2006 4180-011-5310 always used stihl ultra oil, light duty at home use. I have pulled the carb and cleaned, reinstalled, still basically starts right up especially when cold with choke, but will only run for a little bit with the choke on and full trigger throttle, but rpm-wise is only...

Looking to trade my 064 that I have had for several years. Saw came to me as a very low hour unit and I have put 20-25 hours on it since. No cracks, breaks or stripped screws. I have upgraded the following parts: Clutch drum kit (came with a spur drum) Unlimited flywheel Unlimited coil (used)...

Hello, I have a Stihl MS 180C chainsaw. It starts fine and throttles fine as well. However if I were to leave it in idle, it eventually dies. I tried to increase the idle speed but the idle screw had no effect. In examining the carb, I see that the idle screw is not like a traditional screw that...

What’s the deal with the large and small clutch covers? I bought a new MS400 and a 3/4 wrap bar kit for it. The wrap kit also included a bigger clutch cover and bigger dogs. I assumed you needed the bigger clutch cover to fit the 3/4 wrap bar, or the bigger spikes, or both. But that is not...

If anyone has a sane priced 090 clutch that they would sell , I'm looking? I know that they are high dollar items so I'm not unreasonable, just not EBay desperate.

Hey Guys - I'm looking for a decent flat-top 066 cylinder cover with the hole/cut-out for the compression release. I'm building a period-correct short-case poly flywheel saw from the '96-97 era. I've got cash and trade. Thanks!

Does anyone have a set up to take .035 off the bottom of a 66mm cylinder? Don't want anyone to have to buy stuff for it ,ie if you've done one in the past and we can work it out .

Anyone have tried and true formula for improving the 090 cylinder?

I've owned my MS 180c for about 15 years and used it mostly for tree trimming. Today, I started with a full tank and used it for about an hour cutting up fallen limbs 2-5" in diameter. Freshly sharpened, and with a new plug and air filter, it cut great. I took a 30 minute break for lunch, and...

Hey Guys - I need an OEM 660 style crank for the poly flywheel. I started a build only to realize that my case is for the newer crank with the poly flywheel. I got tons to trade and cash. Thanks!

Hi Guys - I'm looking for a new old stock 066 starter housing for one of our new members - MC_Gunny (Cody). Cody bought my nice rebuilt older 066 and wants to dress it up with a new old stock starter housing. He just needs the housing as all of the internals are brand new. Cody was great to...

Visual difference between Farmertec and Stihl trigger parts. I saw a post asking about the quality of the latest kits. Well, I bought a clone MS-660 from someone on E-Bay. Towards the end of the two year square deal warranty it started to get very hard to start and run, so much so, I could only...

Hey Guys - I'm looking for an OEM Walbro WJ carb for 064/066/660. I'm not really too concerned about which WJ it is. I got cash or lots to trade. Thank you!

Hey Guys - I've decided to put this nice old 066 up for grabs - this is from the era just after the "Red Light" saws, so likely around late 1993/early 1994. It's a metal flywheel saw with the upgraded (13 big end roller) OEM crank. I built this in the early days of the pandemic - The carcass...

Hi Guys - A buddy of mine needs a new diaphragm for the oil pump on his 009/011. I gave away all my 009/011 stuff a long time ago. So if someone has a spare, it would be very much appreciated. Thanks!

Hey Guys - I have a need for a number of 020T/MS-2ooT parts- Muffler Top handle/handlebar assembly with all linkages (I'd prefer to get the newer style [200T] of this, but will take anything) Vibration mounts (mainly just the two for top handle) Air filter cover x 2 (Prefer one new) I have a...