Would you trust this.....

[Ryan Browne]

WWJMSD???

Complete the nick in the boot and add a matching leak on the other side. The extra air intakes in the boot give his saws the extra RPM versus other builders (who are overpriced and inexperienced compared to him). Actually all it takes is these cuts in the boot and muffler mod and that'll be good enough for who it's for. Plus, the saw runs great, even if the filter's plugged.

 

[Adirondackstihl]

The nick in the boot could've been caused by anything.
This was a tree service saw and spent its life being tossed in a saw box with 10 other saws.
Under normal circumstances there is nothing that would touch the boot.

I'll go ahead and replace it. Save this one as a spare.

Anyone have a good OEM 1122 (066/660) boot they wanna part with?

 

[angelo c]

WWJMSD???

Daaaamn, that's a "unicorn" intake. Fastest running saw I ever built with that intake. Don't need no porting at all, just run it...

 

[Tor R]

The nick in the boot could've been caused by anything.
This was a tree service saw and spent its life being tossed in a saw box with 10 other saws.
Under normal circumstances there is nothing that would touch the boot.

I'll go ahead and replace it. Save this one as a spare.

Anyone have a good OEM 1122 (066/660) boot they wanna part with?

its the best solution Jeremy, intake boots like that doesnt last and its best to swap it out while the saw still has a good top end.

 

[Adirondackstihl]

its the best solution Jeremy, intake boots like that doesnt last and its best to swap it out while the saw still has a good top end.

Well ya see......that's why the saw is torn down.
They kinda cooked it.

 

[breese]

And here I thought that was some type of Pop-Off valve to make sure your not cheating.....

 

[spencerpaving]

When you remind me I have a good 660 cylinder I'll send ya... Along with a a 346 muffs with a big hole in it

 

[Adirondackstihl]

When you remind me I have a good 660 cylinder I'll send ya... Along with a a 346 muffs with a big hole in it

I have 2 660 cylinders here.
One has some serious transfer that I don't think will clean up and the other once had transfer in it that has some vertical gouges that I'm not real fond of above the exhaust port.
I'll take you up on the 660 cylinder my friend.
Stock cylinder or did you stick you tool in the holes?

 

[spencerpaving]

I have 2 660 cylinders here.
One has some serious transfer that I don't think will clean up and the other once had transfer in it that has some vertical gouges that I'm not real fond of above the exhaust port.
I'll take you up on the 660 cylinder my friend.
Stock cylinder or did you stick you tool in the holes?

Stock....No tool sticking

 

[pro94lt]

I'd trust that over some of the aftermarket ones on 200ts I bought.

 

[Canadian farm boy]

I'll go ahead and replace it. Save this one as a spare.

Anyone have a good OEM 1122 (066/660) boot they wanna part with?

I gotcha buddy. I know I have a couple good used 066 tubes. I'll check em out tonight

 

[Termitebuffet]

The nick in the boot could've been caused by anything.
This was a tree service saw and spent its life being tossed in a saw box with 10 other saws.
Under normal circumstances there is nothing that would touch the boot.

I'll go ahead and replace it. Save this one as a spare.

Anyone have a good OEM 1122 (066/660) boot they wanna part with?

I got 2 brand new oem boots here Jer if you need one....

 

[Adirondackstihl]

I got 2 brand new oem boots here Jer if you need one....

Awesomeness

 

[spencerpaving]

Personally if you have another hole in the intake...I would just add another carb...But that's just me....

 

[Adirondackstihl]

Personally if you have another hole in the intake...I would just add another carb...But that's just me....

*facepalm*

 

[Mastermind]

Add a draft line where that nick is at.....and run it on alky.

Have I gotta tell you everything?

 

[Warped5]

The nick in the boot could've been caused by anything.
This was a tree service saw and spent its life being tossed in a saw box with 10 other saws.
Under normal circumstances there is nothing that would touch the boot.

I'll go ahead and replace it. Save this one as a spare.

Anyone have a good OEM 1122 (066/660) boot they wanna part with?

J, if ya needs one .... I'll send ya one. Just PM your address to me.

 

[Adirondackstihl]

J, if ya needs one .... I'll send ya one. Just PM your address to me.

I got a few leads on a boot.
Appreciate the offer my friend.
If I needs it, I'll let ya know.

 

[Adirondackstihl]

Add a draft line where that nick is at.....and run it on alky.

Have I gotta tell you everything?

What about NOS?

 

[Adirondackstihl]

Anudder member scent this to me for which I am very grateful for.
Just curious what ya'll think?
After 15yrs of staring at a computer screen 40hrs / week, my eyes have a hard time deciphering stuff without pics/closeup