What's on your bench?

[WillG]

Did some test cuts with the 034 and then replaced the carb needle grommet on my Super XL/XL-12 and touched up the chain. 3 strokes on each cutter had it looking great.

Sent from my E6910 using Tapatalk

 

[M2theB]

029 Super with a Blue Tape fuel line and catheter heading to a Warhawk 039

 

[tickbitintn]

On it.....
Not much!
Hadn't seen this thing since September, going to celebrate with what's on it now and go watch curse of oak island.

Sent from my XT1635-01 using Tapatalk

 

[drf256]

@drf256 Does this make my wheel look bigger?

View attachment 220787

I’d need like 4 pairs of cheaters to read that wheel.

 

[Stump Shot]

I’d need like 4 pairs of cheaters to read that wheel.

The only advantage it has is, I don't bump it it all the time, that and it reads 0 - 360 both ways. Otherwise I need my cheaters and a flashlight to read it myself.

 

[dustinwilt68]

Started the day by fixing a broke wire on my 2063/2171 for the on/off switch, then ported the 2511T and last put a new intake and fuel line in the 5105, I made a new clamp for it, I dispise the spring that they come with from the factory, it's the weak spot on that saw for sure.

 

[WillG]

Test cuts with the 346 with dual port muffler. Ordered a new Oregon ProLite 18" bar and Oregon LGX chain for it too.

Took the West Coast spikes off the 034 and put the stock one back on. Also turned up the oiler as it wasn't oiling a lot.

I guess tomorrow I'll make test cuts with the Super XL/XL-12

Sent from my E6910 using Tapatalk

 

[Cut4fun]

Guess this means I can build a couple more 505 2083 54mm if I like now.

Now I have seen two of the oem 2 ring pistons for them. Always want to compare them for kicks.
Also have used a 66 piston in them before too. But little different specs and have to open pin bosses up.

 

[WillG]

Test cuts with the Super XL /XL-12. Did excellent. Just need to tweak the idle speed and mix a tad.

Sent from my E6910 using Tapatalk

 

[WillG]

Recreated my dad's setup from back in the day, an 034 with 20" bar for some cutting this weekend. Also tossed the 16" bar back on the 031 for tomorrow's cutting video.

Sent from my E6910 using Tapatalk

 

[sawnami]

2100 AO and Super 2100 Automatic

Sent from my SM-N950U using Tapatalk

 

[Tor R]

52 hour saw get new bearings & top end:


Ready for freezer:


While waiting for tomorrow heating she lost a couple ears:

 

[dustinwilt68]

New 462 in for a port job

 

[huskyboy]

New 462 in for a port jobView attachment 221378

You better get a cuttin vidja, before and after would be kool .

 

[dustinwilt68]

I think I have a Stihl bar here somewhere. I will try and make that happen, weather permitting.

 

[huskyboy]

I think I have a Stihl bar here somewhere. I will try and make that happen, weather permitting.

Maybe compare your 2171 to it too while your at it. Lol

 

[dustinwilt68]

Maybe compare your 2171 to it too while your at it. Lol

I recently tried a new combo on the 2171, be a nice test

 

[Backtroller]

Rebuilding a 046 carb

 

[WillG]

Nothing tonight except for relaxing. Tomorrow I'm doing a cutting video with the 031. Also cutting up some downed pine at a vacant house down the street.

Sent from my E6910 using Tapatalk

 

[Cut4fun]

Was comparing some poulan 54mm pistons. Some old ones pulled from past saws and some of the new nos and used ones that came in.

Got alittle surprise. Front piston that came in a saw in the past turned out to be aftermarket. Had oem circlips, oem wrist pin, caber ring. Least they were smart enough to do all of that.

As you can see the skirts are freaking so thick on that afm one.