What's on your bench?

[Stump Shot]

Ended up putting a Kawasaki module in this 028 WB, as the condenser gave up. Can tell by its wanting to fire, but only a time or two. If SEM type flywheel is Handy it can be easily converted with the common 0000-400-1300 coil. Or the flywheel broached in the SEM position which is marked on the back.

 

[usmcbuckwild]

Ended up putting a Kawasaki module in this 028 WB, as the condenser gave up. Can tell by its wanting to fire, but only a time or two. If SEM type flywheel is Handy it can be easily converted with the common 0000-400-1300 coil. Or the flywheel broached in the SEM position which is marked on the back.

View attachment 156375

Isn’t the 029 flywheel/coil a direct replacement?

 

[Stump Shot]

Isn’t the 029 flywheel/coil a direct replacement?

Not sure, but it might.

 

[usmcbuckwild]

Not sure, but it might.

I vaguely remember swapping an 029 coil onto an 028WB and someone mentioning a flywheel swap as well.

 

[Stump Shot]

I vaguely remember swapping an 029 coil onto an 028WB and someone mentioning a flywheel swap as well.

That coil fits a pile of saw's.

 

[Onan18]

I swapped a 039 coil onto an 028WB that had points. Didn't swap the flywheel and it worked perfectly. Was unaware there was more than one coil for a WB with points?

 

[Stump Shot]

I swapped a 039 coil onto an 028WB that had points. Didn't swap the flywheel and it worked perfectly. Was unaware there was more than one coil for a WB with points?

Coil for points and one modulated.

 

[redline4]

Isn’t the 029 flywheel/coil a direct replacement?

I did it on one and had to advance the timing some, once I did that it ran great.

 

[Stump Shot]

Just tried to start that 028 after leaving it out in the cold, not a pop.
Started one pull in the warm shop.

 

[beaglebriar]

Just tried to start that 028 after leaving it out in the cold, not a pop.
Started one pull in the warm shop.

Fuggin creamsickle garbage I tell ya...[emoji90]

 

[Stump Shot]

Fuggin creamsickle garbage I tell ya...[emoji90]

Probably the new Champion spark plug in it. Knew I should have tossed it. Lol

 

[J. Loe]

K.
This is a McCulloch pro 10-10 Automatic that I got gratis from an old German man named Werner who worked at the Mac factory in Lake Havasu City.

Cleaned up nice!

Really really clean now no?

I’m gonna get a gotfishon gasket set, a carb rebuild kit, install a new fuel line and filter and maybe, I haven’t tested it yet but maybe put in a new coil.

I’m stoked.
Bet this bugger will pull a 24” bar all day.

 

[Huskygasaxe]

Been busy at work. Home for Christmas. Putting a 181se together.new bearings and crank put in. Case gasket from sveden is ripped! Waiting on another. Merry Christmas all!

 

[Huskygasaxe]

Works been busy

 

[SKEETER McCLUSKEY]

Works been busy

nice!!

 

[Cut4fun]

Husky Jred Partner Poulan folks might know this.

I always just used redneck tools in past to remove them. Looking for part # or numbers. The oem tool that is used to remove rubber anti vibes. Just for these 2 501269702 504125014 That 2 prong tools they make. Think maybe 3 total.

 

[Cut4fun]

Got the info on them already. No need to waste your time looking. 3 of them listed oem

 

[J. Loe]

Did one of my practice run assembly jobs now that I’ve got her all cleaned up.

Seems like a really strong spark but what do I know..
Bright and blue.
New fuel line and filter
to the
Pump side of the carb which seems stiff especially in the circular region....
Meter side seemed stiff as well.

Got her to start up for the 1st time in god knows how long with carb cleaner shot down the pipe but wouldn’t idle...

I’ve got that new carb kit as well as new gaskets coming next week.

I’m excited.
Bet she’ll be a monster.

 

[Dub11]

Did one of my practice run assembly jobs now that I’ve got her all cleaned up.

Seems like a really strong spark but what do I know..
Bright and blue.
New fuel line and filter
to the
Pump side of the carb which seems stiff especially in the circular region....
Meter side seemed stiff as well.

Got her to start up for the 1st time in god knows how long with carb cleaner shot down the pipe but wouldn’t idle...

I’ve got that new carb kit as well as new gaskets coming next week.

I’m excited.
Bet she’ll be a monster.

I got that combo of yellow ones too.

 

[usmcbuckwild]

What are saw surgeons using for epoxy? Not a big fan of JB weld and want something more “professional grade” than walmart epoxy.