What's on your bench?

[Tpagel]

I trimmed right here to let the air horn out
Also cut the back half of the tits that go into the rubber isolators off.

Sent from my SM-J327V using Tapatalk

 

[JohnnyBlade]

Total tweakage.throttle linkage rubbing hard even before trigger is pulled.left isulator pegged all the way foward right insulator pegged all the way backheres the problem area black sharpie highlights what has to be removed.

 

[JohnnyBlade]

This is the problem. 359 elbow is larger from flange to mount. Stock 351 elbow

 

[JohnnyBlade]

Modification done. Time to reassemble.

 

[drf256]

A bit of fuel experimentation.

This is an attempt of mixing 50% Nitro (20% cast0r/30% methanol) with 32:1 mix. 50cc of each.

Not sure what makes up the supernatent. Will retry with 100% Nitro when it arrives for Science.

 

[beaglebriar]

View attachment 139495 View attachment 139496 Modification done. Time to reassemble.

There you go! Whatever camera you are using takes very nice pictures.

 

[dustinwilt68]

All for science

 

[huskyboy]

A bit of fuel experimentation.

This is an attempt of mixing 50% Nitro (20% cast0r/30% methanol) with 32:1 mix. 50cc of each.

Not sure what makes up the supernatent. Will retry with 100% Nitro when it arrives for Science.

View attachment 139505 View attachment 139506 View attachment 139507

The mad scientist dr doing what he does best

 

[Sty57]

A bit of fuel experimentation.

This is an attempt of mixing 50% Nitro (20% cast0r/30% methanol) with 32:1 mix. 50cc of each.

Not sure what makes up the supernatent. Will retry with 100% Nitro when it arrives for Science.

View attachment 139505 View attachment 139506 View attachment 139507

Is that stuff separating that fast?

 

[Cut4fun]

I called that fuel gas mix ( cocktail ). Sort of what I used to run in gas race saw before going over to alky nitro all the way. But I mixed with KL-200 and 24:1

 

[460 magnum]

Should I start up a new thread with this one... "what's in your bathtub"
Waiting on chain and the maxair

 

[huskyboy]

Should I start up a new thread with this one... "what's in your bathtub" View attachment 139513
Waiting on chain and the maxair

Enjoy... if you’ve ever ran a 660 you’ll be impressed how far ahead it is in performance.

 

[460 magnum]

Enjoy... if you’ve ever ran a 660 you’ll be impressed how far ahead it is in performance.

Ran one very little and was kinda disappointed but that could have had something to do with just running a 395 lol...

 

[Duane(Pa)]

A bit of fuel experimentation.

This is an attempt of mixing 50% Nitro (20% cast0r/30% methanol) with 32:1 mix. 50cc of each.

Not sure what makes up the supernatent. Will retry with 100% Nitro when it arrives for Science.

View attachment 139505 View attachment 139506 View attachment 139507

You are your avitar!

 

[JohnnyBlade]

There you go! Whatever camera you are using takes very nice pictures.

Iphone 6s, i always try and use my headlamp to light up the object intead of the flash. Seems less glary. And wer not done yet. 1 more hiccup to go stay tuned.

 

[JohnnyBlade]

Ok so with the larger air horn and filter on there is one more issue. With lid snapped down it pushes the AF and carb assembly down justa smidge. 2 straps down its fine, all 3 and no good. Heres the prob. The bottom of the idle adjuster braket hits the floor of the carb bay. It will throttle through past but will not return till u unsnap lid. Not really wanting to open another small hole in the carb bay i think ill grind the linkage down on the carb. Comments and critisisms welcome.

 

[Lightning Performance]

Ok so with the larger air horn and filter on there is one more issue. With lid snapped down it pushes the AF and carb assembly down justa smidge. 2 straps down its fine, all 3 and no good. Heres the prob. The bottom of the idle adjuster braket hits the floor of the carb bay. It will throttle through past but will not return till u unsnap lid. Not really wanting to open another small hole in the carb bay i think ill grind the linkage down on the carb. Comments and critisisms welcome. View attachment 139521View attachment 139522View attachment 139523

Take a very hot box wrench and push the floor down.

 

[JohnnyBlade]

Take a very hot box wrench and push the floor down.

Damn that sounds like a great idea! Now should i use a 1/2" or 9/16"?

 

[460 magnum]

Damn that sounds like a great idea! Now should i use a 1/2" or 9/16"?

12mm

 

[Dub11]

Damn that sounds like a great idea! Now should i use a 1/2" or 9/16"?

Use a buddies wrench