What's on your bench?

[PA Dan]

My son finished building the 026 that is now his! We fired it up today but have to go back in. It flooded and might have to lower the metering lever. He got a little excited when it fired up!

 

[Canadian farm boy]

My son finished building the 026 that is now his! We fired it up today but have to go back in. It flooded and might have to lower the metering lever. He got a little excited when it fired up!

Nice looking saw Dan. You're son should be proud. Great job buddy

 

[X 66 stang347 X]

Husky 372 xtorq. Owner said it just stopped running. Took muffler off and piston looked ok, had some carbon streaks. Tried pulling the recoil to see the rest of piston and it wouldn't move. Bottom end is locked up. By the looks of the bottom end there's very little oil getting down there. No oily residue on the crank rod at all. Con rod bearing is toast..

You know what oil and Ratio?

 

[Tor R]

Any chance I could buy the "G" parts off your 353? I could send you a regular flywheel for the 353 too.

I dont plan to pick parts from the 353 G I got.
I do have a few spare G parts for 346/353, need to look through what I have stored, it may be a full G set except front handle&switch..

 

[Tor R]

345 - year 99, self modded crankhouse!


Those are for 345 - year 03, with luck one of them can be used.


Gotta admit I hate clamshells, can't find any positive side with them, if I can rebuild one 345 it's not gone stay in my house.

 

[Brewz]

1128... meet 1122

 

[Derf]

I dont plan to pick parts from the 353 G I got.
I do have a few spare G parts for 346/353, need to look through what I have stored, it may be a full G set except front handle&switch..

PM me info, thanks

 

[t4driller]

You know what oil and Ratio?

Not sure. About a year ago I got a couple 372s and some other saws off him. Almost all of them had bad con rods. I asked what oil/ratio and he said 50/1 with whatever oil. I told him he needs to start running a good oil at 40/1. I see he didn't take my advice. When I dumped the fuel out of the tank of this 372 it was blue.

 

[TJ the Chainsaw Mechanic]

Yesterday I went to the shop and serviced up my ms170 and homelite super xl. Then went through the fuel system on my project mcculloch 610 and she lives! Runs like a Top to. Has a 20 inch bar, gonna sharpen the chain and see how she does....if she pulls the bar well I'll throw a 24 or 28 inch on there......big saw needs a long bar.....even if it is only 60 cc. lol Actually that saw was capable of a 28" from the reading I've done.

 

[Tor R]

Husky 40, a tad free porting....


This one start to be complete



Thought she was to pretty to trow in the bin, left to buy an Meteor.

 

[Tpagel]

Followed me home
I like this old logo.


Sent from my iPhone using Tapatalk

 

[dall]

does it run travis

 

[dustinwilt68]

Put new plastics on a MS440 today, that was about all the time I had today, tomorrow installing a MMWS 365 top end and hope to run my MMWS 357xp, can't wait to see how they run.

 

[Tpagel]

does it run travis

It is free but I couldn't get it to hit on the old gas in it.
I will drain it and see after I have time to give it a bath


Sent from my iPhone using Tapatalk

 

[Keith Gandy]

250c with a leakin fuel tank at the seam

 

[Keith Gandy]

137 with a leaking intake boot

 

[Keith Gandy]

Man this 2152 JRed didnt like this leakin transfer cover!

 

[USMC615]

My son finished building the 026 that is now his! We fired it up today but have to go back in. It flooded and might have to lower the metering lever. He got a little excited when it fired up!

Nice...good looking 026!

 

[PA Dan]

Nice...good looking 026!

Thanks buddy!

 

[beaglebriar]

Clinton D50 that my buddy gave me. This one's gonna get restored and live in my game room.

For now I'm going to see if she'll run. I just have to hear what it sounds like!