What's on your bench?

[t4driller]

Looks very nice. I hate painting orange since it covers so poorly for me. I did a simplicity tractor once and that paint seemed almost translucent for the first few coats.

This paint didn't seem to bad. First coat I always go real thin. I bet I have 15 or more coats of paint on it. I priced out paint from Napa to shoot with my gun, and it would have been almost 200 for just the paint, reducer, and harder. So I decided to try out this paint. I can say that this kind comes out thicker then the paint I used from tsc. I'll see how it holds up. I'm going to get a skid plate/ protector for it.

 

[Backtroller]

That's good to know about that brand. Yes people don't realize the costs of all components that go into spraying especially if you're only painting a case or a few small parts.

 

[Dub11]

Hey guys I need some help on a 026 I freshend up with new lines air filter.and cleaned the carb. My problem is it acts real cold blooded. I can set the carb it will start easy then when it gets warmed up want to bog. I can tune the bog out but after setting a day its a real pain to start. Am I missing something? Thanks.

 

[dall]

richen up the low side maybe ?

 

[dustinwilt68]

Got this in the mail today looks to be in nice condition. Needed to add some Jonsered to my lineup.

 

[beaglebriar]

Hey guys I need some help on a 026 I freshend up with new lines air filter.and cleaned the carb. My problem is it acts real cold blooded. I can set the carb it will start easy then when it gets warmed up want to bog. I can tune the bog out but after setting a day its a real pain to start. Am I missing something? Thanks.

Did you put a kit in the carb?

 

[dustinwilt68]

My dad's 026 did the same thing even after a new kit in the carb, swapped it for a cheap Zama and problem gone.

 

[Brewz]

Just re-keyed an 064 limited flywheel to run an 066 unlimited coil

Worked perfect!

 

[Woodrow]

Got this in the mail today looks to be in nice condition. Needed to add some Jonsered to my lineup.

Is that the one from White River Junction?

 

[dustinwilt68]

Came from Minnesota

 

[t4driller]

Just re-keyed an 064 limited flywheel to run an 066 unlimited coil

Worked perfect!

View attachment 56013

Nice!! How did you determ8ne how far to go? I'd like to do the same to my 066rl.

 

[Dub11]

richen up the low side maybe ?

Ive played with that till the cows came home. Ive got it now were it will start after 10 or so pulls then let it run on high idle for a min ( which Iam not a fan of) then its alright.

Did you put a kit in the carb?

No it looked good but Iam leaning that way now.

When I first put it back together I set to factory one turn out and it popped off in 3 pulls but when it warmed up acted like it was running rich. Then got set were it wouldn't bog off idle and sounded good but the last 3 day trying to start it is a chore.

 

[dall]

hows the choke lever and 1 turn out should be close

 

[Dub11]

And when the guy brought it to me is looked like the choke spring was soft and killing it and stuff. There was a lot of oil coming out of the muff and all over the front of the saw.

 

[beaglebriar]

Ive played with that till the cows came home. Ive got it now were it will start after 10 or so pulls then let it run on high idle for a min ( which Iam not a fan of) then its alright.


No it looked good but Iam leaning that way now.

When I first put it back together I set to factory one turn out and it popped off in 3 pulls but when it warmed up acted like it was running rich. Then got set were it wouldn't bog off idle and sounded good but the last 3 day trying to start it is a chore.

Sounds like the diaphragm might be weak. You sure the saw doesn't have any air leaks? Did you throw a new plug in it?

 

[Dub11]

Sounds like the diaphragm might be weak. You sure the saw doesn't have any air leaks? Did you throw a new plug in it?

yes to the new plug

 

[Dub11]

My dad's 026 did the same thing even after a new kit in the carb, swapped it for a cheap Zama and problem gone.

Did that zama have the high and low adjustments?

 

[dall]

id toss the zama and put a 194 on it

 

[dustinwilt68]

194 was a good bit more, yes it had the high and low adjustments, long as that Zama is running good it is staying put.lol my dad's saw is all stock, and to be honest it cut the majority of his wood and mine last year, so the zama has already pd for itself.

 

[Dub11]

id toss the zama and put a 194 on it

Iam pretty sure it has the 194 on it now