What's on your bench?

[mettee]

You got more important *s-word to do!

Shut the h3ll up

 

[Billy Currie]

Sending this 620 out today.

 

[trooney]

Almost done..a few smalls to get...

 

[trooney]

Just waiting on a new rotor post, springs, and clutch drum..

 

[slackinoff]

Titanikel 272 on my “experimental” saw to test against an oem 272 cylinder saw.

1. 

 

[PA Dan]

Just waiting on a new rotor post, springs, and clutch drum..

View attachment 336015

Looks great Tom!

 

[slackinoff]

Finished, waiting for the sealant to cure….

 

[mettee]

 

[Ronie]

Pretty much finished up my 461 today, pop up piston, muffler mod and advanced the timing.

https://www.youtube.com/shorts/893CzIKUM7Q

 

[huskyboy]

 

[WillG]

Finished up a parts replacement and tune up/oil change on a newer Lawn Boy push mower with Kohler XT650 engine. Needed a new auto choke arm/thermostat, governor spring and anti surge spring. Adjusted rpm to 3000 and running sweet. Air filter was just plugged solid so I have a new one on the way.

Sent from my E6910 using Tapatalk

 

[Ketchup]

Two broken starters and a busted chain brake spring.



Not to mention an inch thick layer of crud inside everything. Cleaning takes longer than repairs.

 

[rogue60]

McCulloch 250 I restored years ago. Was very low hr to start with still had the original rim barely worn with yellow paint on it from the factory.
I ended up giving it away to a mate I couldn't take to it slow revving woefully slow cutting for my liking I think the super is more desirable of the two. 066 spoils ya lol

 

[Sagebrush33]

I haven't even seen my bench. Guess I should gets to cleaning it off.
Garage is an ice box during winter months. Clutter adds quick.

 

[Ronie]

Picked this up off ebay and it just arrived, the piston looks good and has good compression.. I thought that after a couple of Stihls I would go back to Husqvarna but they are starting to grow on me, the down side is the price of Stihl parts.

 

[Ronie]

I put a little fuel in it and it fired right up.

https://youtube.com/shorts/npr0Fj0WbBs?feature=share

 

[WillG]

Put the new air filter in the Kohler and test ran it, ran perfect. Just need to write up his invoice tomorrow evening and deliver it Friday night.

Also got a Honda GX390 on a Target street saw running with a new carb. Remounted water tank and runs nice. Tomorrow I just need to replace the plug, change the oil and pick up an M6x1.0 wing nut for the air filter cover.

Sent from my E6910 using Tapatalk

 

[Sagebrush33]

Picked this up off ebay and it just arrived, the piston looks good and has good compression.. I thought that after a couple of Stihls I would go back to Husqvarna but they are starting to grow on me, the down side is the price of Stihl parts.

View attachment 336228 View attachment 336229

One of my all time favorites. While buying bearings and some other small parts to rebuild mine, I came across a NOS case. Nabbed that up and collected almost everything to build a 2nd, with mostly NOS parts. Gonna do a hybrid this time though.

 

[Ronie]

One of my all time favorites. While buying bearings and some other small parts to rebuild mine, I came across a NOS case. Nabbed that up and collected almost everything to build a 2nd, with mostly NOS parts. Gonna do a hybrid this time though.

If I had a 460 cylinder I'd be building another hybrid.

 

[Sagebrush33]

If I had a 460 cylinder

I dooos