What's on your bench?

[tickbitintn]

Well it's not on the bench but definitely glad it's not in my garage anymore picked up this quality harbor freight motor from a guy I work with for 40 bucks now I got 60 bucks in this stupid wood splitterView attachment 319913

It will pay for itself on the first tank of fuel.
Your back will thank you as well. [emoji6]

Sent from my XT1635-01 using Tapatalk

 

[RI Chevy]

Two words. Ran Cher I’m going to do some stuff but. Hopes are not high. Lol

It's like pumping money into a YUGO to try and get more performance out of it...lol

 

[decableguy2000]

Well it's not on the bench but definitely glad it's not in my garage anymore picked up this quality harbor freight motor from a guy I work with for 40 bucks now I got 60 bucks in this stupid wood splitterView attachment 319913

That Harbor freight engine should last a while, the one on our splitter has out last the 2 briggs engines that were on it. If it dies tomorrow morning, I'll put a new one on it by lunch.

 

[Shane¹]

That Harbor freight engine should last a while, the one on our splitter has out last the 2 briggs engines that were on it. If it dies tomorrow morning, I'll put a new one on it by lunch.

Had a Briggs on it and don't think it was original one

 

[Maintenance Chief]

Jug and slug were fine but he is upgrading 5cc to a 460 slug and jug. Got a crank off eBay. Should be ok after

Did not know that was a thing, thanks for the info.
Whats a crank go for?

 

[David Young]

Did not know that was a thing, thanks for the info.
Whats a crank go for?

Used eBay $50-60
New 2 hundo

 

[Kiwioilboiler]

Well duh...anchors usually go to the bottom!

UnFriend.

 

[merc_man]

Little dolmar on the benchnfor a cleaning and sharpen. The past weekend was the dirst time i used it. Runs pretty good butni git to order sone anti vibe hushing for it. It flops around like a wet noodle. Will put it away till i get sone in

Sent from my SM-G950W using Tapatalk

 

[merc_man]

Also got the muffler from my 034 that my son butchered. So the new muffler isnt quite as deep as the original old style. I am thinking of taking the gasket and making a spacer the same as it out of 1/8 inch metal to take up the space then I think it should work. Will probly use a thin layer of muffler goop to seal and hold it on to the muffler side then the regular gasket inbetween that and the cylinder.

Sent from my SM-G950W using Tapatalk

 

[Kiwioilboiler]

No Bueno.

 

[Stevetheboatguy]

No Bueno.
View attachment 320013

Someone needs a kick in the sack for that one........



Steven

 

[tickbitintn]

Someone needs a kick in the sack for that one........



Steven

Or two to make sure ya get both!

Sent from my XT1635-01 using Tapatalk

 

[Maintenance Chief]

No Bueno.
View attachment 320013

I can see them saying, "Well that ain't going anywhere!"

 

[Ketchup]

No Bueno.
View attachment 320013

Is that welded on or just solder?

 

[Kiwioilboiler]

Is that welded on or just solder?

I haven't grinded on it yet mate, but it sure looks like "farmworker barn weld" to me.

 

[RI Chevy]

No Bueno.
View attachment 320013

Redneck fix!!! Lol unreal

 

[Johnmn]

Finally getting to my 2171W! It's all tore down, case halves soaking in the parts washer overnight.

 

[Wanab]

Wheel-O-Fortune!

 

[WillG]

MTD Yard Machines 10 hp snowblower for a couple items..oil change, new plug, replaced skid shoes and recoil rope.

Sent from my E6910 using Tapatalk

 

[tickbitintn]

Dug this guy off a shelf, quick look over and then fired it up and ran it for a bit.
Always liked the sounds of it.
Trying to clean up and downsize the herd a bit so I'll probably be sending this one down the road.
Haven't been able to run a saw for a while and (I might) have one or two too many (Yeah like that's a thing!!!)
Lol

Sent from my XT1635-01 using Tapatalk