What's on your bench?

[MustangMike]

I remember those days … I am so thankful everything I have … saws, roto tiller, splitter, cars are all electronic ignition! If I never see a set of points again I will be happy!

 

[usmcbuckwild]

I remember those days … I am so thankful everything I have … saws, roto tiller, splitter, cars are all electronic ignition! If I never see a set of points again I will be happy!

Not much I can do in converting an 056 over. It has an 045 crank with points

 

[redlight066]

Amazing there was no case damage and the fuel tank/rear handle didn’t have a scratch

 

[trooney]

I wish peolle would clean their saws once in a while. Didnt even come from a tree company.

 

[Onan18]

I'll just leave this right here...

 

[tickbitintn]

View attachment 183763
I'll just leave this right here...

Oil thread in three, two, one... LOL

Sent from my XT1635-01 using Tapatalk

 

[dustinwilt68]

I wish peolle would clean their saws once in a while. Didnt even come from a tree company.
View attachment 183671 View attachment 183672

Shame it didn't have air injection.

 

[huskyboy]

It’s amazing how much cleaner a saw stays when the chain is actually sharp too... lol

 

[trooney]

Shame it didn't have air injection.

It would probably clog it!! Air injection aint the cure all for that disaster!!

 

[trooney]

Shame it didn't have air injection.

It would probably clog it!! Air injection aint the cure all for that disaster!!

 

[trooney]

Wow, 4 times! A record!!

 

[Stevetheboatguy]

Wow, 4 times! A record!!

And that's what she said


Steven

 

[Tor R]

Got the time to work a tad with a carb today..

Those need to be removed:


Gone remove a bit casting too:


Prepped and ready for the dremmel:


This is how the famous HDA 199 accelerator pump look:

 

[Czed]

Got a builder 266 cylinder case's top cover and 268 recoil
In great shape.
A couple 272 cylinders for other projects.
After pressure washing
It'll be ready for assembly.

 

[beaglebriar]

Got the time to work a tad with a carb today..

Those need to be removed:
View attachment 183827

Gone remove a bit casting too:
View attachment 183828

Prepped and ready for the dremmel:
View attachment 183833

This is how the famous HDA 199 accelerator pump look:
View attachment 183834

Can you eliminate the accelerator pump Tor?

 

[dustinwilt68]

Couple new saws showed up today, these are booth just for me.

 

[Tor R]

Can you eliminate the accelerator pump Tor?

yes you can DJ.
I have to fine study the channel who goes to the accelerator pump (would'nt like to block a channel if it feed other systems)

 

[usmcbuckwild]

Morning all.

 

[redline4]

I'm in need of some advice from the Husqvarna guys.
Husky 359. While it is apart, should I remove the transfer covers and reseal them, or leave them well enough alone?
Saw had an air leak from the pto crank seal and intake.
I am not familiar enough with them to know if it's a case of "better do it while in there" or "don't open that can of worms".

 

[beaglebriar]

I'm in need of some advice from the Husqvarna guys.
Husky 359. While it is apart, should I remove the transfer covers and reseal them, or leave them well enough alone?
Saw had an air leak from the pto crank seal and intake.
I am not familiar enough with them to know if it's a case of "better do it while in there" or "don't open that can of worms".

The 359's were never really a problem. I never heard of the sealing issue until the 5 series came about. Others my have different opinions but I'd leave them be unless you pull them to do some port work. Then you should reseal.