Saw video thread

[RI Chevy]

Gotta tighten the chain son. Lol

Sent from my SM-G930V using Tapatalk

 

[T.Roller]

Gotta tighten the chain son. Lol

Sent from my SM-G930V using Tapatalk

That's how I store them. Don't want to leave one with a tight chain. I always loosen them when I'm done cutting.

 

[Definitive Dave]

a couple of my 365s idling

 

[RI Chevy]

That's how I store them. Don't want to leave one with a tight chain. I always loosen them when I'm done cutting.

I was just funnin ya. LOL I do the same thing.

 

[Deets066]

How loud is it when you run that? Louder than the dual port front cover?

Sent from my SM-G930V using Tapatalk

It's not that bad at all

 

[Deets066]

I'll add that the tune does change a little, but if I'm gunna be running it all day I'll just warm it up and tune it to 14,800. Throughout the day it will go up to 15,200 or 15,500

 

[RI Chevy]

Not to bad at all. Runs nice!

Sent from my SM-G930V using Tapatalk

 

[Manofstihl066]

McCulloch pro mac 850
first cut after port work.

Great looking saw Jim. Sounds awesome

 

[Backtroller]

In talking with CFB I decided to trace the wire screen to flashing material to make mine "convertible" I figure I can remove the sheet metal to test and not be out anything on my Hybrid

 

[Backtroller]

It's hard to see but the flashing is black. That is not a hole. I have yet to try it out. Been a little busy

 

[Canadian farm boy]

In talking with CFB I decided to trace the wire screen to flashing material to make mine "convertible" I figure I can remove the sheet metal to test and not be out anything on my Hybrid View attachment 81239 View attachment 81241

It's hard to see but the flashing is black. That is not a hole. I have yet to try it out. Been a little busy

Looks great Pat.

 

[Backtroller]

Thanks. I couldn't have some sloppy looking muffler cover running one of your cylinders. That would just be wrong and insulting.

 

[Chainsaw Jim]

Great looking saw Jim. Sounds awesome

Thank you. I was hoping that a port job wouldn't change the signature McCulloch exhaust note. I was quite pleased to hear it still has that growl.

 

[Wolverine]

Thank you. I was hoping that a port job wouldn't change the signature McCulloch exhaust note. I was quite pleased to hear it still has that growl.

Sounds awesome!!

 

[Frank bierce]

McCulloch pro mac 850
first cut after port work.

Sounds awesome..and looks to have some grunt!!

 

[Chainsaw Jim]

looks to have some grunt!!

Lots of grunt. I was putting a good medium load on it.

 

[Dub11]

So this is a 55 I'm going to attempt to spif up for my uncle. Was wanting to make an honest baseline for before and after by letting it fall through the cut. @Stump Shot

 

[Stump Shot]

So this is a 55 I'm going to attempt to spif up for my uncle. Was wanting to make an honest baseline for before and after by letting it fall through the cut. @Stump Shot

Looks like you're off and running, good luck with your build.

 

[Frank bierce]

So this is a 55 I'm going to attempt to spif up for my uncle. Was wanting to make an honest baseline for before and after by letting it fall through the cut. @Stump Shot

Great to see a stock/ported showdown from the same saw. If/when I get into some porting...I will attempt doing before and after of saws worked on.
Is it me, or did the chain sound a bit tight?

 

[Stump Shot]

Great to see a stock/ported showdown from the same saw. If/when I get into some porting...I will attempt doing before and after of saws worked on.
Is it me, or did the chain sound a bit tight?

Look at the bottom of the bar after he pulls out of the cut for your answer, I believe.