Saw video thread

[deye223]

Definitely photoshopped both saw's appear to be running hardnose bar's and cutting timber? We all know that's impossible! lol

Speaking of which I found my old stihl durobar out the back room the other night after we were talking about it on the forum might have to give it a run after I get the angle grinder out .

 

[ferris]

Speaking of which I found my old stihl durobar out the back room the other night after we were talking about it on the forum might have to give it a run after I get the angle grinder out .

Try it, the only negative thing for me is the weight compared to a modern light weight bar.
I like my 20“ hardnose bar on the 462 with 404

 

[WillG]

55 Rancher that I went through. New fuel line, filter, carb kit, intake boot, impulse grommet, David Young carb base repair, and plug. Setup 3/8 7 pin. 20" .050 bar, Oregon EXL Powercut chain.

Sent from my E6910 using Tapatalk

 

[Maintenance Chief]

55 Rancher that I went through. New fuel line, filter, carb kit, intake boot, impulse grommet, David Young carb base repair, and plug. Setup 3/8 7 pin. 20" .050 bar, Oregon EXL Powercut chain.

Sent from my E6910 using Tapatalk

I'm gonna start sending these to you as I find them in dumpsters! Lol
Great job Will, thats an old stand by saw for alot people.

 

[WillG]

Thanks! Now I want one for myself!

Sent from my E6910 using Tapatalk

 

[RI Chevy]

Your Stihl 034 will out cut that little rancher Will...

 

[malk315]

Your Stihl 034 will out cut that little rancher Will...

How many CC is 034? I'll bet the 51 I rebuilt will take it. Challenge accepted. We need a GTG ... DAMN COVID!

Sent from my Pixel 3 using Tapatalk

 

[RI Chevy]

Not sure Eric. Probably 58, 59ccs. But it's a Stihl. Made to run and work...
Hooskies made for fixin at GTGs and stuff. Just sayin..[emoji2957]

 

[WillG]

The 034 is 56.5 cc. 55 Rancher is 53.

Sent from my E6910 using Tapatalk

 

[RI Chevy]

Run it!!! Lol

 

[WillG]

I will!

Sent from my E6910 using Tapatalk

 

[RI Chevy]

Sharp chain, cut wood. Get rid of da Hooskies

 

[WillG]

My 357 seriously embarrassed my 034. Same cc's but performance piston and exhaust.

Sent from my E6910 using Tapatalk

 

[RI Chevy]

Yes, factory hot rod. It should run fasta.
357 is a keepa.

 

[lehman live edge slab]

Also few different cylinders used on the husky 55, don’t really see it beating an 034 stock to stock some of them were pretty impressive actually.

 

[av8or3]

I’ve run nothing but old saws for the last several months. I thought I’d run my 462 this afternoon and see how much different they could be. I could not believe how this thing just melts wood (by comparison) and how really effortless (again, by comparison) using it is. Lightweight and really just stomps thru hardwood.

 

[TreeLife]

Yes, factory hot rod. It should run fasta.
357 is a keepa.

There were a few from each manufacturer that were pretty hot to trot out the gate. 357 is definitely one. 034 super, 044, 064/66...stihl made some kick ass saws back in the day and they're making some again for sure.

064 will be my next saw...then a 592 when they come out the gate. Mr Mastermind will get that one to play with.

 

[RI Chevy]

Nice Dominick!

 

[Moparmyway]

Moparmyway ported 880
36” 404 RM 9 tooth in hickory
First few cuts, still tuning her

 

[RI Chevy]

Nice Kevin. Good thing you have a Simington Square Grinda.
All I could see was Spahks flyin!!!
Did run well though. I'd like to see some test runs with 8 pin and 9 pin same everything else.