Miller Mod Saws and the CS-500P Echo!

[Miller Mod Saws]

Alright she is back together. It's still very well behaved and even starts easier. When I do my testing I have an 18" .325 bar on this saw and the other saw came with a 20". Any preferences as to the vid. I can already tell you after sinking it into the wood pile she is much stronger. How much. Well we will see.

 

[Miller Mod Saws]

I forgot to mention I set the squish on this saw at .020" which netted me this. Lol.

 

[fin460]

subbin in for some videos

 

[Mastermind]

Nothing wrong with that work Carl. Looks damn good to me.

 

[Jughead]

interesting

 

[Miller Mod Saws]

Alright guys. Video isn't that impressing but I did get descent gains. I went ahead and muffler modded the still stock saw. I can tell you I ran this saw most of the morning but switched back to an 18" bar and smaller wood. It shines butch better in that. But in the vid I'm using the stock 20" .325 that came with the new saw.

 

[Miller Mod Saws]

Muffler modded vs ported 20" .325 stock bar and chain. Enjoy! In oak!

 

[fin460]

Come cut some hedge with it

Sent from my E6782 using Tapatalk

 

[fin460]

Both saws look gay, but saw two was certainly a lot stronger

Sent from my E6782 using Tapatalk

 

[Miller Mod Saws]

Come cut some hedge with it

Sent from my E6782 using Tapatalk

Lol. I did all morning. It runs nice in hedge with a
325 18 good chisel chain. Like I said it's more impressive when you actually use the saw like I think it should be. Much faster and torqueier when you using it for little stuff.

 

[Miller Mod Saws]

Both saws look gay, but saw two was certainly a lot stronger

Sent from my E6782 using Tapatalk

Come grab her if ya want and put it threw the paces while I decide where to go with saw 2. Lol.

 

[Mastermind]

Final numbers?

 

[Miller Mod Saws]

Final numbers?

110/125/ and the intake I widened to 55% and just slightly blended down. Exhaust is 65% width. Muffler mod is just the tube removed with the front of the oem deflector opened up.

 

[Miller Mod Saws]

If i get time later I may go grab a vid of these 2 running a 325 18 inch bar in say 12-14 in oak. Much more impressive. Lol.

 

[Miller Mod Saws]

Saw #2 after running this one I'm not sure where I'm going add just a little more comp. I know that. I'm gonna shorten up the blowdown I know that. The exhaust I'm thinking of leaving it a tad lower and I'm really considering epoxing the intake. Maybe go with 112/124/75 with a normal square intake. Gain some more case compression.

 

[Mastermind]

I looked thru my notes.....but I can't find any on the 500p.

 

[Mastermind]

Unlimited ignition?

 

[Miller Mod Saws]

Unlimited ignition?

Well maybe. It dosnt drive my tac funny like a normal rev limiter but she gives her up at 13k unloaded out of the wood.

 

[Miller Mod Saws]

I looked thru my notes.....but I can't find any on the 500p.

Ugh O. Hope ya got a good memory. I sure dont!

 

[Miller Mod Saws]

Well maybe. It dosnt drive my tac funny like a normal rev limiter but she gives her up at 13k unloaded out of the wood.

Or I just don't have her opened up enough yet to pile a rev limiter. Lol.