HUSQVARNA HUSQVARNA THREAD

[Seachaser]

The tether came out with the cap and I put it back in. I tightened it down and threads seem to be holding for now. I may order a new cap if it leaks or does it again.

 

[Firewood Hoarder]

Anyone know of a close spray paint color match for a Husky? I have a 2100 I am wanting to clean up a bit and prevent further oxidation on.

 

[Squareground3691]

Anyone know of a close spray paint color match for a Husky? I have a 2100 I am wanting to clean up a bit and prevent further oxidation on.

https://a.co/d/cwpA556

 

[Maintenance Chief]

Anyone know of a close spray paint color match for a Husky? I have a 2100 I am wanting to clean up a bit and prevent further oxidation on.

Hemi orange, engime paint is pretty close .

 

[Firewood Hoarder]

Hemi orange, engime paint is pretty close .

This saw isn't and probably never will be a show piece... just want to make it less ugly and protect what's left of it. Will grab some hemi orange next time I'm at the store

 

[Maintenance Chief]

This saw isn't and probably never will be a show piece... just want to make it less ugly and protect what's left of it. Will grab some hemi orange next time I'm at the store

The good thing about engine paint is that it's gas/oil resistant.

 

[300whisper]

Any ideas what i could do with this plating chip. Its a xpw cylinder. It had some transfer on the lower exhaust that cleaned right off.

Grind with diamond stone slightly above chipped part, cut with carbide tip and round towards transfers. I did that with my Meteor cylinder, no chipping so far -> I pulled cylinder after some milling work to see the results.

 

[300whisper]

Family picture after some service and tuning from few days ago.
Rear R-L couple of 357XPG, OE/NE 346XGP, 340/346
Front R-L OE 372XPG, OE 362/372XPG, NE 346XPG, 351/346G

 

[president]

Anyone know of a close spray paint color match for a Husky? I have a 2100 I am wanting to clean up a bit and prevent further oxidation on.

its ( real orange ) in a tremclad rattle can

 

[Woodslasher]

its ( real orange ) in a tremclad rattle can

I bought a can of genuine Husqvarna Orange spray paint online, can't get much closer than that.

 

[Ronie]

This saw isn't and probably never will be a show piece... just want to make it less ugly and protect what's left of it. Will grab some hemi orange next time I'm at the store

Rust-Oleum Has a Husqvarna orange. I painted this 288 with it.

 

[qurotro]

Rust-Oleum Has a Husqvarna orange. I painted this 288 with it.

View attachment 412472

Fuel resistant paint?

 

[Ronie]

Fuel resistant paint?

I don't remember if it is or not, it's in their Farm and Implement line of paints.

 

[Powerstroke Cowboy]

Does anyone have a 395 or 394 piston laying around they could grab a dimension off of?

I'm looking for a dimension from the top of the wrist pin, to the top of the piston.

Thanks in advance!

 

[Czed]

Anybody got a pic of a 346xp carb area and vent line routing
I'm putting one together that was in pieces in a bucket.

 

[Squareground3691]

592 , .404 , 32”

 

[Gullet]

592 , .404 , 32” View attachment 414004

I hate you... lol

 

[Adam G]

If anybody is in need of new OEM 3120 XP cylinders, my dealer just confirmed they’re under $200 right now and in stock.

 

[heimannm]

I have a 257 in the shop that needs the plastic "cradle" that is part of the throttle rod 501876803.

Any suggestions on where to find one, or a good work-around?



SawSalvage / Traverse Creek has the sealing collar 501799401

Mark

 

[Squareground3691]

I have a 257 in the shop that needs the plastic "cradle" that is part of the throttle rod 501876803.

Any suggestions on where to find one, or a good work-around?

View attachment 415063

SawSalvage / Traverse Creek has the sealing collar 501799401

Mark

husqvarna 254, 257 chainsaw throttle control link and guide

Part: throttle link and guide. PN 501 87 68-03 Condition: good used/working shape Fits: Husqvarna 254, 257

chainsawr.com