how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

[Louie B]

Good morning
Just poured the first cup

 

[Hinerman]

Oh, and Thomas.....


View attachment 147601

Made my wife laugh. She wants me to send it to her. Got one for you too:

 

[WKEND LUMBERJAK]

Crisp 40 this morning. Have a safe day.

 

[rsting]

Morning everybody. Hope everyone has a great day today. Weatherman is calling for rain here tomorrow.

 

[Hedgerow]

 

[Hedgerow]

Morning everybody. Hope everyone has a great day today. Weatherman is calling for rain here tomorrow.

 

[Workshop]

Morning everybody.

 

[Semotony]

Morning everybody.

Good morning

 

[WKEND LUMBERJAK]

View attachment 147745

So positive.

 

[Cat 525]

Morning all! Nice for the pheasants forever kids day yesterday! Nice today! Maybe try beans later if ground will hold us!

 

[67L36Driver]

Morning midlanders!

Watching the front porch for the days entertainment to arrive.

 

[Locust Cutter]

Afternoon all! Had the day off, so I did some chores this morning, got dinner working in the crock pot (Sausage, potato and kale soup w/spices and some cream). About to go back where we were cutting Saturday with the 9010 to noodle some 24"w -x- 22"l Hedge logs to get them on the S.S. a bit easier. We horsed a few on and it did absolutely fine, but with the lift fubar right now, noodling is the word of the day. Then probably haul a few loads of beans for the neighbors, if they have their case going today.

 

[67L36Driver]

Assembly of the 200t progresses. Piston crown clearance is .035” sans gasket. [emoji20]

Maybe use the belt sander and take .015” off the cylinder base. [emoji848]





[emoji48]

 

[Dub11]

Assembly of the 200t progresses. Piston crown clearance is .035” sans gasket. [emoji20]

Maybe use the belt sander and take .015” off the cylinder base. [emoji848]


JMS said a sharpe line was good for .020 lol




[emoji48]

 

[Hinerman]

View attachment 147745

I either found a hernia or created one laughing at this. You should put on a suit and tie and be this weatherman for Halloween.

 

[Hinerman]

View attachment 147744

I think you found a new avatar, LOL

 

[Hedgerow]

I either found a hernia or created one laughing at this. You should put on a suit and tie and be this weatherman for Halloween.

I figured you'd like that one..

 

[Hinerman]

Tree service was taking down a pin oak one block over. Drove my trailer over and they loaded some limbs. The trunk was over 36” and knotty as heck so I passed. We need a mini loader.

 

[Cat 525]

That pin oak tuff stuff when full of pin knots! Where it got it's name I reckon!

 

[Locust Cutter]

Well, while cleaning the 201T, I ended up filing the key on the fly wheel down until I had about 5-9° advance on the timing. Then, worked on the carb and drilled the muffler. It runs A LOT better now, though it's still not a Husky. It did pick up a good bit of throttle response, but far more torque. I think I may enlarge the holes in the muffler a tad more, ensure that I do actually have 10° of advance and tune the carb a hair more and then I'm satisfied.

I also shot some crappy video while noodling the two rounds of Hedge:

I still need to pop the fly wheel off and retard the timing a bit, but last time I tried, the flywheel didn't want to come off, after tapping it well with a rubber mallet. I might need a puller for that sob...