how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

[Sawdust Man]

Another good day working in the woods, sawin' down trees.



Tom cut a beautiful white oak.... I didn't measure it, but I think it's around 24"

 

[Sawdust Man]

Hauled three & a half loads....... in two trips....lol.

 

[Sawdust Man]

@Workshop Steve, this place is about 1/2 mile down hwy HH, just around the corner from the stamp.

 

[Hedgerow]

Question for all the saw mechanics out there..

Saw starts and gushes fuel from both jets..

Full throttle with both high and low screws turned all the way in still gagging with fuel.

Possible causes??

This should be fun..

 

[WoodAbuser]

Question for all the saw mechanics out there..

Saw starts and gushes fuel from both jets..

Full throttle with both high and low screws turned all the way in still gagging with fuel.

Possible causes??

This should be fun..

Sounds like the needle and seat are shot.

 

[Hedgerow]

Sounds like the needle and seat are shot.

It acts like it’s just flat stuck open...

I fogged the whole shop.. had to leave the blue haze was so thick..

I didn’t realize a carb could burp that much fuel even with the high and low circuit closed off.

 

[Fishnuts2]

I found a replacement diaphragm one time that had a 2 mm button on it instead of just a rivet in the middle. Needles didn't have any effect and was cured by filing the button down.

 

[Sawdust Man]

Good morning folks.

Heading out shortly to saw up more trees....if it doesn't rain too much..

I don't know what is wrong with Matt's saw... but if it were mine, I'd try a carb rebuild.

 

[Workshop]

Morning everybody.

 

[srcarr52]

It acts like it’s just flat stuck open...

I fogged the whole shop.. had to leave the blue haze was so thick..

I didn’t realize a carb could burp that much fuel even with the high and low circuit closed off.

The metering level is probably set very high and the needle is getting held open.

 

[nbbt]

Good morning folks.

Heading out today or tomorrow to mark some trees for cutting in a week or two (I hope). Leaves were partly down last Sat. morning and were dropping fast.

 

[JimBear]

It looks like the season is a changing, the weather dweebs are clucking about snow flurries here Sat. night & Sunday…

 

[Sawdust Man]

It looks like the season is a changing, the weather dweebs are clucking about snow flurries here Sat. night & Sunday…

View attachment 394640

And it's been 80° here the last few days.....what about fall? I want a refund....

 

[Hedgerow]

The metering level is probably set very high and the needle is getting held open.

Has to be..

Although it managed to do it on it's own. Since my neighbor used it all last year with no issues.

Still amazed that much fuel can get by those high and low screws.. It's an impressive amount.

New parts inbound.

 

[srcarr52]

Has to be..

Although it managed to do it on it's own. Since my neighbor used it all last year with no issues.

Still amazed that much fuel can get by those high and low screws.. It's an impressive amount.

New parts inbound.

It could be a really stiff diaphragm.

 

[JimBear]

@Dub11

Are you all prepared for winter up there ?

 

[Sawdust Man]

More saw fun today...
Broke out the ported 372, with enough bar to saw em down from one side..... I really like to have more bar than tree when falling
I'm guessing we cut around 30 trees today.


26" ash.


30 red oak.

 

[Hedgerow]

Hard to beat a good 372..

 

[Hedgerow]

A good 9010 is one of the few...

 

[Hedgerow]

Or one of carr’s 394’s...