how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

[Bryan Newton]

Morning yall

 

[Workshop]

Afternoon everybody.

 

[BrettL]

Good afternoon y'all

 

[Bryan Newton]

Afternoon yall

 

[Semotony]

Afternoon gents, ay not be so good. Guessers are claiming 33° for a Lil while with sun on surface of drive. A few minutes more the temp will be freezing again, the angle of sun less direct for iced snow on drive that is uphill to road.
Unless the asphalt chips scattered on each side of center collected enough heat to liquefy the bit of snow on top.

 

[Sawdust Man]

Evening folks.

 

[BrettL]

I'm going to buy crank seals for my 036. Are the aftermarket seals any good or should I buy OEM or are they all the same?

 

[Sawdust Man]

The ups guy showed up with our new toy today.
DeWalt 20v cordless miter saw.

I'm liking it pretty good so far.... we used it all afternoon on the pig barn.

 

[JimBear]

I'm going to buy crank seals for my 036. Are the aftermarket seals any good or should I buy OEM or are they all the same?

@67L36Driver

 

[WoodAbuser]

The ups guy showed up with our new toy today.
DeWalt 20v cordless miter saw.

I'm liking it pretty good so far.... we used it all afternoon on the pig barn.
View attachment 359389

Always working all the angles.

 

[WKEND LUMBERJAK]

I'm going to buy crank seals for my 036. Are the aftermarket seals any good or should I buy OEM or are they all the same?

Are you keeping it?

 

[mrxlh]

Is everyone warming up nicely?

 

[KS Plainsman]

Is everyone warming up nicely?

Almost too much. It got to 63 today and we even had a decent wind.

 

[Hedgerow]

The ups guy showed up with our new toy today.
DeWalt 20v cordless miter saw.

I'm liking it pretty good so far.... we used it all afternoon on the pig barn.
View attachment 359389

Alas....

The only 20v tool I don’t have.. didn’t even know it existed..

 

[Hedgerow]

Is everyone warming up nicely?

Not yet...

Still cold and windy..

 

[Sawdust Man]

Alas....

The only 20v tool I don’t have.. didn’t even know it existed..

You need one.........

Do you have a cordless framing nailer?
I'm shopping for one, but I'm not convinced the DeWalt is the the way to go.
I mostly have DeWalt cordless tools, so it makes sense to stay with one brand for battery reasons if the nailer is good.

 

[Sawdust Man]

Is everyone warming up nicely?

Still pretty doggone cold around here..... though they are still claiming it'll be 65 on Thursday.

 

[BrettL]

Are you keeping it?

Yes

 

[plcnut]

You need one.........

Do you have a cordless framing nailer?
I'm shopping for one, but I'm not convinced the DeWalt is the the way to go.
I mostly have DeWalt cordless tools, so it makes sense to stay with one brand for battery reasons if the nailer is good.

I don't think I would buy the DeWalt framing nailer. I plan to buy the Milwaukee when I need one.
I really like my Flex/60 volt DeWalt batteries. The 6" angle grinder is the only 60 volt tool I have, but it is great.

 

[mrxlh]

I don't think I would buy the DeWalt framing nailer. I plan to buy the Milwaukee when I need one.
I really like my Flex/60 volt DeWalt batteries. The 6" angle grinder is the only 60 volt tool I have, but it is great.

Might want to keep close tabs on the Milwaukee stuff. We use it in an industrial setting daily, the fuel cordless impact’s quality have gone to *s-worde…