how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

[WKEND LUMBERJAK]

Back from Lawrence KS..
Boys got to warm up..
Just in time to have the officials call off throwing cause it was too dark!!

All the boys were throwing great too.
Levi was warming up at 140 and the kid from Moore OK dropped about a 180' bomb in warm ups.
Would have been a good night..

Got to chat with Kenneth a bit though. So all was not lost.

Dang nice evening. Enjoyed the chat . That 180 would be hard to beat.

 

[WKEND LUMBERJAK]

Nice this morning. 76* get it done early

 

[Mastermind]

Have a great day fellers.

 

[Hinerman]

Nice this morning. 76* get it done early

Headed to the wood lot in a few minutes to split for a few hours. Meeting a kid there who wants to earn some money stacking wood. I have plenty to stack for him.

Have a great day fellers.

You do the same.

 

[67L36Driver]

Morning midlanders!

Wellness check on Jim later this am. Give him a chance to sleep in before pullin' his chain.

 

[67L36Driver]

Not going back tomorrow.
Got too much stuff to get done.


And fish to catch.

IIWM (if it were me) I'd do the fish first!

 

[Workshop]

Mornin' Y'all.

 

[concretegrazer]

 

[Time's Standing Stihl]

Back from Lawrence KS..
Boys got to warm up..
Just in time to have the officials call off throwing cause it was too dark!!

All the boys were throwing great too.
Levi was warming up at 140 and the kid from Moore OK dropped about a 180' bomb in warm ups.
Would have been a good night..

Got to chat with Kenneth a bit though. So all was not lost.

How old was the kid that dropped a 180? Pretty impressive.

Work blows....6 down, 6 to go

 

[Hedgerow]

How old was the kid that dropped a 180? Pretty impressive.

Work blows....6 down, 6 to go

Senior.. Most of them were.
A few going to throw in college.

 

[cobey]

Today was transom rebuild day

 

[cobey]

Turned out pretty ok,
I did it old school as it came from the factory. All the brackets and hardware was there except one handle
I will have less than 300 in the boat when it's done.
If I do it again I will do my super strong
Transom with 1 inch angle and a 2x12
The last one I did I could stand on
The 20 hp anti cavitation plate

 

[sawnami]

View attachment 25518
View attachment 25519
Today was transom rebuild day

BTDT on a fiberglass boat. It was a bad feeling to look back and see the transom fiberglass at about a 45 degree angle when you gassed it because the wood inside was rotted out and finally gave way. I was at Table Rock Dam when I noticed it and could just imagine seeing my motor sink into 200 feet of water with my boat following it.[emoji50]

Sent from my SM-T900 using Tapatalk

 

[Workshop]

I had a boat once. There's a reason I don't have a boat now, too.

 

[SteveSS]

Evening fella's. Another project in the books today after I mowed the ditches out front. Upgraded roosts for the chickens. I increased their sleeping quarters four-fold today. Should make for happy chickens.

 

[cobey]

BTDT on a fiberglass boat. It was a bad feeling to look back and see the transom fiberglass at about a 45 degree angle when you gassed it because the wood inside was rotted out and finally gave way. I was at Table Rock Dam when I noticed it and could just imagine seeing my motor sink into 200 feet of water with my boat following it.[emoji50]

Sent from my SM-T900 using Tapatalk

That's always been my fear
I have seen where a aluminum boat
Can pop open like a can of beans
Because of bad transom falure

 

[Hedgerow]

Just got back from lake and cleaning fish.

Back out at 5:30.

Swimming by 9:30..

Home by 11:30 and picking up round bales.

Not enough dark hours in a day right now.

 

[67L36Driver]

Just got back from lake and cleaning fish.

Back out at 5:30.

Swimming by 9:30..

Home by 11:30 and picking up round bales.

Not enough dark hours in a day right now.

2 pm naps works for me.[emoji6]

 

[sawnami]

Hmmmm Okaaaaaay

Sent from my SM-N910V

 

[mdavlee]

Hmmmm Okaaaaaay

Sent from my SM-N910V

That's funny