High Quality Chainsaw Bars Husqvarna Toys Hockfire Saws

how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

Semotony

Here For The Long Haul!
Local time
10:11 PM
User ID
5078
Joined
Jan 16, 2018
Messages
2,698
Reaction score
13,882
Location
Missouri
Country flag
Far enough that I am sent to st Louis VA. I'm choosing between north on N to 32 in Bismarck, west to Caledonia South on 21, or west on N to 21 north to 32 west in either case over to Houston. In state I may have cell connect to make up for getting close only. If the crow flies I'M three miles south of Bismarck ten miles from either Arcadia valley or Farmington. If I find the arial shot of my property it may have co-ordinates for prescise :jaja-no: description:eusa_whistle: :jaja-no:. Now that social insecurities have been added to the disability I can afford more gas & can start sooner in case I wander too far off course.
Just the smart A$$ in me covering a variety Matt

View attachment 147072[/QUOTE]

Barely visible is a white road West out of Farmington that goes to Ironton.About equidistant from each end am I. So there are two ways to get to 32 west at 21 to get to Houston. Going toward Ironton I am usually bat outa hell, so prolly that way past entrance to the lake. Less than three miles walking according to my younger brother. 28 miles to drive, from the farm Dad retired to. Know a bit of the area
 

Only the Tony

Hiding in the back of the class.
Yearly GoldMember
Local time
10:11 PM
User ID
958
Joined
Feb 27, 2016
Messages
3,066
Reaction score
23,656
Location
SW MO
Country flag
How deep?

And this might be the only time a Stihl is cheaper.......
505 foot. Hit a pocket of muddy water at 125' and we discussed options and prices. Could have pulled casing and re-cased to 168' or line what was already done. Decided to just leave casing at 105' and have them put in a liner. Hopefully that will be done tomorrow depending on weather. Putting out about 150 gallons a minute now, will drop around half after liner installed.

I could have bought several new 3210's for what this hole cost.
 

Workshop

Mastermind Approved!
Yearly GoldMember
Local time
10:11 PM
User ID
613
Joined
Jan 19, 2016
Messages
7,633
Reaction score
41,672
Location
Nixa, Mo.
Country flag
Evening everybody.
Traded off that pull behind mower this evening. Got another generator. The guy I got it from said he bought it from a sale at a farm. I asked if it was a dairy farm, he said yes it was. I figure it was their back up generator. A home made unit, it's an Onan 2 cyl RV generator mounted on a home made trailer about 6 feet long. Pretty slick setup, can tow it down the highway.
I'll get pics tomorrow .
 

plcnut

Jesus is LORD
Local time
10:11 PM
User ID
917
Joined
Feb 20, 2016
Messages
1,426
Reaction score
8,872
Location
Mansfield, Missouri
Country flag
Evening everybody.
Traded off that pull behind mower this evening. Got another generator. The guy I got it from said he bought it from a sale at a farm. I asked if it was a dairy farm, he said yes it was. I figure it was their back up generator. A home made unit, it's an Onan 2 cyl RV generator mounted on a home made trailer about 6 feet long. Pretty slick setup, can tow it down the highway.
I'll get pics tomorrow .
I have 1-1/2 of those generators.
The newer one is intact, but I tore down the older one to use the engine to replace a bad one on my Miller welder/generator.
My new one uses the windings of the generator as the starter for the engine. It's pretty neat.
 
Top