HOMELITE Homelite Thread

[67L36Driver]

On holes with sharpe edges, one can chamfer with a drill bit.

 

[Hoggwood]

Went out to get a short load of "easy to manage" firewood for the folks today. It runs well after swapping the top end. But, it is one high compression saw without the gasket now. Needs substantially more load.

 

[sweepleader]

Looks good, but I don't see how you can ever have too much power...

 

[TJ the Chainsaw Mechanic]

I love using my MS460 on small wood. lol Need to get me a big ol Homelite someday.

 

[sawfun]

Three 50" bar Homies at the PNW gtg.

 

[exSW]

Three 50" bar Homies at the PNW gtg.
View attachment 24536

You need to start a thread for the PNW gtg

 

[TJ the Chainsaw Mechanic]

Three 50" bar Homies at the PNW gtg.
View attachment 24536

NOT FAIR!!!!!!!!!!!!!!!!!!!

 

[Sty57]

Picked up a 7-19c today.

 

[sawfun]

NOT FAIR!!!!!!!!!!!!!!!!!!!

There was also a 60" bar on Sheldon's 3100g and a 40" on my 900g. I ran out of time or that 900G would have been wearing a 58" bar I have for it. and that did not include the long bar Stihl's, Mac's, 166, and a Husky 2100. all wearing 50" or longer bars for the six and a half foot diameter log Bob had there for us to play with.

 

[TJ the Chainsaw Mechanic]

There was also a 60" bar on Sheldon's 3100g and a 40" on my 900g. I ran out of time or that 900G would have been wearing a 58" bar I have for it. and that did not include the long bar Stihl's, Mac's, 166, and a Husky 2100. all wearing 50" or longer bars for the six and a half foot diameter log Bob had there for us to play with.

Now yer killing me. haha!

 

[sawfun]

Worse yet, I just found a Titan this weekend and may end up with an 11 foot bar for that 296cc monster. That will make my 090g with 8 foot bar seem small by comparison. Just plain silly.

 

[67L36Driver]

Worse yet, I just found a Titan this weekend and may end up with an 11 foot bar for that 296cc monster. That will make my 090g with 8 foot bar seem small by comparison. Just plain silly.

Pics or it didn't happen.[emoji847]

 

[sawfun]

When I get the bar setup on the saw I will post pictures of it, for sure.

 

[jake wells]

my super xl auto has a leaking seal on the clutch side and i noticed the seal is NLA would you guys know if a national 253747 would fit?
i would greatly appreciate the help.

 

[DSS]

my super xl auto has a leaking seal on the clutch side and i noticed the seal is NLA would you guys know if a national 253747 would fit?
i would greatly appreciate the help.

That will fit the manual oiler saws, but I'm pretty sure the auto oiler saws take a different PTO side seal and I don't know of an aftermarket

Tim and some of the other guys know tons more about the homelites than me though [emoji111]

 

[jake wells]

That will fit the manual oiler saws, but I'm pretty sure the auto oiler saws take a different PTO side seal and I don't know of an aftermarket

Tim and some of the other guys know tons more about the homelites than me though [emoji111]

i read through the homelite sticky on the other website and a guy by the name of eccentric said the seal would work on the clutch side of super xl auto saws.
i was only trying to verify.

 

[hseII]

i read through the homelite sticky on the other website and a guy by the name of eccentric said the seal would work on the clutch side of super xl auto saws.
i was only trying to verify.

Cause he would no. [emoji38][emoji38]

 

[countryhog]

Rebuilt a C5 couple years ago. Used it several times for hard cutting. No problems. Put it up in the spring with no fuel, etc
Took it down one cold winter day, fueled it up, and started it. It would barely idle and at high speed it would wander. I tried a few things to no avail and put it up cause I had other saws to fix
Took it down again other day. Fuel filter, spark plug, new fuel, cleaned carb. Fuel lines still pliable. Still runs like crap.
Need suggestions

 

[psuiewalsh]

Points/condenser?

Sent from my XT1585 using Tapatalk

 

[countryhog]

Thanks. Gonna check them. Guess I was wanting a miracle, don't hafta take it down response. Got any idea what the capacitance should be on the condenser?