PAST Chain buildoff-April 24

[Dolkitafreak]

I am hosting a chain build off, anyone is welcome.

Chains will be 60dl 3/8 .050 ran on a woods ported 6100, in aspen (subject to change, will confirm tomorrow). Wood will be an 8x8, there are no rules, just send a chain and see how you do! Saw will be ran by a third party, who is not entering a chain, so there will be no bias. All for fun!

3 cuts will be timed, slowest removed, remaining 2 will be averaged.


I must have the chains by April 23, they will be tested the 24th.

 

[Wolverine]

7 or 8 pin? I only have .050.

 

[Dolkitafreak]

7 pin is all I have for small spline, .050 is perfect.

 

[Armbru84]

Will the guys who send chains get them back?

Anything for winning?

6100 done for torque or speed? Some guys may want to tailor a chain depending on that. I assume this is the Egan ported 6100?

Single cuts or double cuts and average the two?

Any thoughts on how to prorate the cuts depending on how the wood density may change as you go through the log?

 

[Definitive Dave]

Anything for winning?

Smack talking rights ?!?

 

[Duane(Pa)]

 

[Armbru84]

Smack talking rights ?!?

I mean there is always that...always good to get something too. Loop of stock chain or something would be cool.

 

[Definitive Dave]

Ethan is a great guy,, still in high school, not sure there will be any prizes. Hoping there will be video of the runs and pics of the nice cutters to share, myself.

 

[Time's Standing Stihl]

I mean there is always that...always good to get something too. Loop of stock chain or something would be cool.

How about a kick in nuts for losing [emoji23][emoji23]

 

[Duane(Pa)]

You should get some wild ass chain! No holds barred. PLEASE post as many pix of the entries as you possibly can

 

[Armbru84]

Ethan is a great guy,, still in high school, not sure there will be any prizes. Hoping there will be video of the runs and pics of the nice cutters to share, myself.

I know...I will donate 2 loops of new EXL to the winner. 3/8 .050 72DL.

 

[Dolkitafreak]

Will the guys who send chains get them back?

Anything for winning?

6100 done for torque or speed? Some guys may want to tailor a chain depending on that. I assume this is the Egan ported 6100?

Single cuts or double cuts and average the two?

Any thoughts on how to prorate the cuts depending on how the wood density may change as you go through the log?

If you’d like your chain back, send $8 with the chain and I’ll get it back to you. For the winner, I’ll toss in a stock loop of EXL, and maybe a vallorbe file or something.

 

[Deets066]

You need a list of who is entering

 

[Dolkitafreak]

Yes to the Egan built 6100. Little bit of both, I can post a video so guys have something to go off of. Tuned a hair leaner than the limiter (13.8) but can pull a 24 in hardwood, so take that how you will!

 

[Dolkitafreak]

You need a list of who is entering

So far, nobody has contacted me about entering, I asked for chains by the 23rd, that was I have a day to get them a designated letter or number to keep things unbiased.

 

[Deets066]

List of entrees

Deets066

 

[Deets066]

Maybe somebody could send an 8 tooth sprocket with their chain?

 

[Dolkitafreak]

If that’s preferred, then sure. I’m about to make a video real quick, just to give perspective

 

[Deets066]

If that’s preferred, then sure. I’m about to make a video real quick, just to give perspective

If it’s an Eagan ported 6100, then I’d venture to say an 8 pin is preferred. Lol

 

[Definitive Dave]

need to run the same rim for all the saws or it isn't a valid chain competition, just sayin...