Any Chinese chainsaw and chinese parts discussion

[Ronie]

@srcarr52 I marked the leading edge of the magnet on both flywheels and put a piston stop in the cylinder. I was just trying to see if there was a difference between the OEM and the Farmmac cranks.

 

[Ronie]

First real cuts with the Neotec 372. It ran pretty good in that hard seasoned oak. The guy at our local sawmill said he's got fresher oak for me, I just need to get up with him.

 

[Maintenance Chief]

First real cuts with the Neotec 372. It ran pretty good in that hard seasoned oak. The guy at our local sawmill said he's got fresher oak for my, I just need to get up with him.

Runs as good as any 372xp I've ever seen!

 

[HumBurner]

First real cuts with the Neotec 372. It ran pretty good in that hard seasoned oak. The guy at our local sawmill said he's got fresher oak for me, I just need to get up with him.

Nice! I cut some white-oak last week in a similar state of seasoned. Standing for years hung up. Right into the stove, no fuss. Lot of folks look at the outside and think it's rotten and punky, they don't look at the grain. Minimal loss of BTUs.

 

[thedude74]

First real cuts with the Neotec 372. It ran pretty good in that hard seasoned oak. The guy at our local sawmill said he's got fresher oak for me, I just need to get up with him.

That thing runs damn good Ronie! Subbed to your channel.

 

[Czed]

First real cuts with the Neotec 372. It ran pretty good in that hard seasoned oak. The guy at our local sawmill said he's got fresher oak for me, I just need to get up with him.

Runs strong
Neotec replaced the cylinder kit on mine with a 39.00 mtlano jobbie.

 

[Ronie]

That thing runs damn good Ronie! Subbed to your channel.

Thanks

 

[Ronie]

Runs strong
Neotec replaced the cylinder kit on mine with a 39.00 mtlano jobbie.

It surprised me how fast their customer service handled the problems I had, there wasn't all that back and forth, send us a video crap.

 

[Ronie]

Since seeing @Maintenance Chief's 372 with a big bore I decided to give a big bore a try. I took a chance and ordered 5 because the pics in the ad looked good, one of them just showed up and it looks as good as the pics. I'll post the timing numbers and squish how it came out of the box in a few. I also made a new mandrel out of 2 pieces of scrap rod screwed together and a new block to cut the squish.

 

[Powerstroke Cowboy]

Since seeing @Maintenance Chief's 372 with a big bore I decided to give a big bore a try. I took a chance and ordered 5 because the pics in the ad looked good, one of them just showed up and it looks as good as the pics. I'll post the timing numbers and squish how it came out of the box in a few. I also made a new mandrel out of 2 pieces of scrap rod screwed together and a new block to cut the squish.


View attachment 415873View attachment 415874View attachment 415875

What brand is the cylinder? Or is it a white box cylinder?

 

[Ronie]

What brand is the cylinder? Or is it a white box cylinder?

It's a white box

 

[Ronie]

Two more just showed up and they look just like the first one. I got the timing numbers off the first one, without the base gasket the numbers are,

EX 102
TR 126
IN 71
Squish .035

 

[Powerstroke Cowboy]

It's a white box

Okay, thanks! I've got a bb cylinder that has the same markings on the combustion chamber. It's from a white box as well.

 

[Maintenance Chief]

Since seeing @Maintenance Chief's 372 with a big bore I decided to give a big bore a try. I took a chance and ordered 5 because the pics in the ad looked good, one of them just showed up and it looks as good as the pics. I'll post the timing numbers and squish how it came out of the box in a few. I also made a new mandrel out of 2 pieces of scrap rod screwed together and a new block to cut the squish.


View attachment 415873View attachment 415874View attachment 415875

If anything I'm not usually referred to as a good example! Lol
It is crazy that, although I understand porting techniques and timing I didn't do much more than a "woods port " on that cylinder. It performs extremely well despite the abuse I throw at it.
I frequently let the young staff at work use it and they love it!

 

[Czed]

Found a use for my g395 box
Had to take yellow bastard in for emergency bladder surgery
He was hurting so bad i couldn't get him in a carrier
It'll cost more than a couple of g395s

 

[ammoaddict]

Found a use for my g395 boxView attachment 415889
Had to take yellow bastard in for emergency bladder surgery
He was hurting so bad i couldn't get him in a carrier
It'll cost more than a couple of g395s

Hope it doesn't cost you too much. How's that g395 doing? I think I want one.

 

[HumBurner]

Found a use for my g395 boxView attachment 415889
Had to take yellow bastard in for emergency bladder surgery
He was hurting so bad i couldn't get him in a carrier
It'll cost more than a couple of g395s

Poor feller! He doing alright post-surgery?

 

[Czed]

Hope it doesn't cost you too much. How's that g395 doing? I think I want one.

No idea i heat cycled mine a few times and it's been setting ever since.
Haven't even cut with it I've been running the orange 288 a lot it's been flawless other than the decomp leaking.
It really is a nice saw and easily oem power i have a few oem 288s
Whenever i get time it's getting a ported cylinder and 066 piston.

 

[Czed]

Poor feller! He doing alright post-surgery?

He's at the vet's they called and said he was doing fine after surgery and they were keeping him until monday.
He got severely ill in one day while i was at work i got home at 2am and he was immobile.
When i went to work he was walking and eating.

 

[Hulpio]

Beautiful Lion you have there. Hopefully he's ok. Our four legged companions have only one huge disadvantage which is too short lifetime. I should have taken an other dog when my dog was 6-7yrs. It would be easier to cope when the time comes if I would still have at least one furry friend.