V-stack filters

[srcarr52]

You noticed problems with the K&N on just the older huskys or on saws in general? I could see the 2100 doin some damage to a filter, lots of vibes, not to the user but to the saw

That's where I have had failures of K&N's is on a 2100.

 

[srcarr52]

Shaun, you gots any stacks that'll fit a 266?

Not in stock, I usually just make them to order. The Angry Elf 288 should fit, I make mine 2" OD for different filter options but the 2.25" should have lots of options too.

 

[Al Smith]

My 2100 has a large K and N with a V stack .I suppose it's a PNW thing because it came from some island off of Washington state . I have no idea if this saw has been worked over or not .Pulls over hard is all I can say .

 

[Cut4fun]

EDITED TWICE NOW TO FIX ALL MY MISTAKES

Ok I will try to answer a few questions on the Angry Elf Engineering stacks.
Currently four sizes/styles all custom made.
#1 fits dang near all of the Stihls from the 026 up to the MS660 with a 2" OD.
#2 fits the MS880, 088, 084 and 3120, it also fits the 075/076 and the crazy WB carb that some of us have been playing with, it has an OD of 2.49"
#3 is for the Husqvrna 288, 281, 61, 66, 266 and some of the Pioneer models with a stock 288 elbow and has an OD of 2.25", the carb bolts are slightly offset.
#4 is for the Husky 2100 , 2101 and 298, it has an OD of 2.125"
We would be open to having other models produced based on demand.
We have all four of them with Unifilters as well as just the bare stack.
Search on Angry Elf in my store for pics (sorry no nudes).
We looked at both the K&N and unifilter when we started and went with unifilter because they are washable and oil able, and seem more suited to chainsaw abuse in milling, etc.
Dave

that nickname is so fitting.

 

[Adirondackstihl]

that nickname is so fitting.

Who is it?

 

[Definitive Dave]

7 of the different models we have tested from unifilter
I will say it is nice to be able to go into any motorcycle specialty store and buy K&N, Unifilter and a bunch of different filter options, as well as oil and cleaner.

 

[CR500]

Anyone think it is possible to fit a UNI under the stock HD of cover of a Dolmar?

Sent from my non internal combustion device.

 

[Toad22t]

View attachment 35785




I bet this wouldn't fit too bad either

This is the same style filter my 181 eliminator had and my 288 high top has.

These filter elbows are NLA but I believe @skippy has some available. These filters are still available through the dealer as of now.

 

[Backtroller]

There not much room for the height. Most UNI filters are taller than 2 1/2" I think the smallest black ones I posted on page one are 2 3/4" and 3". You will also need to take into account a flange to tighten it too.

The bigger problem seems to be this tiny HD elbow Stock non HD elbow in the top picture. The bottom picture has the HD elbow sitting next to the non HD.

What isn't visible from the picture is how narrow the bend is on the HD elbow. The internal area on the HD is very small. Sorry for the poor photo.

 

[Toad22t]

Here is a link to KN and you can design what you want and see if they have it.

http://www.knfilters.com/mobile/univcone.aspx

 

[RI Chevy]

Cool.

 

[Toad22t]

Here is an angry elf v stack and uni filter from Dave!


KN filter on my 288



Stock 288 filter

288 high top next to a standard 7900



My 298 with another angry elf v stack.

I have also had a 288 and 044 vstack from Shaun.

I don't have anymore 272 HD filter elbows and I can't remember the the bolt pattern was straight across or angled.

 

[Deets066]

Not much room in here. So, would a 288 elbow fit and give me more height to put the stack on?

@mdavlee

 

[mdavlee]

There might be enough room. I've probably got a 288 elbow at home somewhere.

 

[Deets066]

There might be enough room. I've probably got a 288 elbow at home somewhere.

Would a 395 high top elbow work?

 

[mdavlee]

Possibly

 

[Deets066]

I still have the one I was gunna send you. I'll try it. Otherwise I could pull the one off my 2100

 

[1990Husky262]

wouldn't the bolt holes being at an angle be a problem though. looks like an application where somebody needs to custom build something.

 

[Toad22t]

View attachment 36224

Not much room in here. So, would a 288 elbow fit and give me more height to put the stack on?

@mdavlee

The standard 288 filter neck sits at quite an angle. I measured it once and iirc it was almost an half inch from front to back.

This is how the eliminator adapter worked!

 

[Redfin]

That's where I have had failures of K&N's is on a 2100.

Have you tried any of the uni with the rubber base?