Yet again .... JMSSAWS strikes

[RI Chevy]

Nice Kevin. Awesome job on that rebuild!
Definitely done right, now. Holds RPMs really well and should only get better and better.
I think sawmikazee will really like it! [emoji106]
[emoji481]

Sent from my SM-G930V using Tapatalk

 

[blsnelling]

Sounds great.

 

[Moparmyway]

Nice Kevin. Awesome job on that rebuild!
Definitely done right, now. Holds RPMs really well and should only get better and better.
I think sawmikazee will really like it! [emoji106]
[emoji481]

Thanks Jeff

I'm about ready to box her up, then I looked at the muffler and caught a glimpse of something, grabbed the T27 and took the first picture, so I did a little bit more work, then took the second picture

 

[RI Chevy]

Double screen or did you just go with the larger opening screen?

Sent from my SM-G930V using Tapatalk

 

[Moparmyway]

Double screen or did you just go with the larger opening screen?

Its a factory DP muffler. It had two different screens, I like them looking the same, so they now have 2 of the same screens and I opened them both just a little more

 

[RI Chevy]

Cool. Weird with the 2 different screens.

 

[junkman]

For performance i like those big screens ,but when using the saw for many hours on end i like the stock ones ,they are a little quieter in the exhaust tone .

 

[Moparmyway]

For performance i like those big screens ,but when using the saw for many hours on end i like the stock ones ,they are a little quieter in the exhaust tone .

I just wear ear plugs ....... its all the ssme that way

 

[RI Chevy]

I prefer to let them breath and get the heat out. I also wear ear plugs. [emoji106]

Sent from my SM-G930V using Tapatalk

 

[junkman]

WHATTT!!!

 

[RI Chevy]

WEAR YOUR EAR PLUGS BRYAN. LOL

Sent from my SM-G930V using Tapatalk

 

[sawmikaze]

Saw runs great kev, thanks a ton.

All you guys that donated or did whatever .. I appreciate it.

Thanks.

 

[CR888]

That's a nice running saw now. An 8pin .404 sprocket is pretty big fast gearing that takes a lil omph to cut large wood. Hope Ryan enjoys his saw now.

 

[RI Chevy]

Vids when you can please. [emoji106]
Glad you finally got an awesome saw!


Sent from my SM-G930V using Tapatalk

 

[sawmikaze]

Vids when you can please. [emoji106]
Glad you finally got an awesome saw!


Sent from my SM-G930V using Tapatalk

My online forum days are about done buddy.

Ill send some to kev if I ever get a director to take a video, i just wanted to pop in and give thanks where it's due.

 

[Adirondackstihl]

My online forum days are about done buddy.

Ill send some to kev if I ever get a director to take a video, i just wanted to pop in and give thanks where it's due.

Why you leavin bro?

 

[PA Dan]

Umm ...........
Ryan ...........
I dont know how to say this -------BUT

You need a new clutch, yours is broked

Well he's kinda used to that! Lol![emoji23]

 

[Moparmyway]

That's a nice running saw now. An 8pin .404 sprocket is pretty big fast gearing that takes a lil omph to cut large wood. Hope Ryan enjoys his saw now.

Thank you Sir !!
I was hoping someone would notice
The setup, the wood, and the RPM she held.
I really had to lean into her, I thought that I wasnt going to be able to stuff her .............. maybe after she breaks in some, it'll become even more difficult

IIRC, he runs a 3/8 drive with an 8 tooth on a 32 or 36 B&C ................ Ought to really make him sweat and struggle to pull her down without the dogs

 

[Angelr]

Impressive, a wheel. 404-8 needs lots of power

 

[CR888]

I bought a near new 660 out of the states from an AS member then Randy ported it and modded the oiler. Its a damn good saw for our hardwoods and cuts fast with 404, I run a 7pin but have an eight too & when in your hand next to other .325/3/8 sprockes you realise how much bigger they are. Old big torquey saws with cutting rpm's of 7k like the big sprockets to get some chain speed, new saws cutting at 10-12k really need some power to do it well. Job well done!