What's on your bench?

[Leerod83]

View attachment 217676

View attachment 217677

Those look awesome Scott. Very professional looking.

 

[WillG]

Replaced the intake boot, partition wall and clamp on my 346xp conversion. Air leak repaired!

Sent from my E6910 using Tapatalk

 

[JohnnyBlade]

Nothing is going to be on my bench for a little while.

Going to be preoccupied

View attachment 217541

Little 7lb 14oz girl. For all you guys that have known we were expecting.

Mom and baby are doing good.

Likely I won't be around here much for a while but I'll be back. Bunch of you have my number if you need to get ahold of me.


Later guys

Steven

Congrats Steve! Gald all is well with ur baby girl and momma. Should we start sending the Redbull? Id send u some extra time and sleep but i havent found it on the interwebs yet

 

[JohnnyBlade]

View attachment 217676

View attachment 217677

Looks amazing Scott!

 

[heimannm]

 

[JohnnyBlade]

Nothing to
Crazy. Tank vent on a 350.

 

[Canadian farm boy]

Completely reworked a 390xp muffler. Original deflector is cut off and the outlet covered over and welded solid. Added 1 outlet on either side of the can. Had to trim the top cover to make room for the FW side deflector. Heat tape added to the brake handle just to be safe.

 

[rogue60]

Sorted my doorbell hair trigger it's ready to put up now oh and done some bar art it's a sawfish! the white lines are the number of times I've thrown the chain and it's wrapped around my legs no not really lol it's actually the number of times I've managed to start a 7+ cub saw all on my own.
Might get some much needed rain this arvo figgers crossed.

 

[Backtroller]

Ordered a brand new OEM recoil from Australia on 12/19. The exchange rate is quite favorable. It arrived 1/10 which in my book is fast.

 

[redlight066]

Rebuilding a 372. Check out the new fuel filter. Ya think it need a new one?

 

[redlight066]

Funny how quiet a stock saw is. Lol

 

[huskyboy]

Cutting yesterday on one of my tsumura bars, I must’ve had a log pinch the tip (don’t know how the eff I did that as I’m not one to usually do that). Didn’t notice it till the chain was just starting to smoke at the tip... a “oh chit” moment lol. Today I fixed the spot on the tip circled in red, you can see the slight discoloring. The fix for this is quite simple... use a flat head screwdriver slightly bigger than the groove and hammer it down lengthwise into the rail several times to ease it back open. Checked final fitment with a proper gauge.

Sprocket spins freely, we’ll see how long it holds up but it seems to cut well now. The tip doesn’t seem to be as strong as a sugi bar, which is odd as both are made in japan. Must be because of the 4 rivets vs the 5 in the sugihara tip?

 

[RI Chevy]

Crap. Glad you fixed it Mason. You could always grab a new tip too...
Keep one in your stock for the just in case moment...

 

[huskyboy]

Crap. Glad you fixed it Mason. You could always grab a new tip too...
Keep one in your stock for the just in case moment...

I think I am gonna get a extra tip. We bore cut a lot which is hard on tips. Especially in the cold.

 

[drf256]

This clean azz 660. The jug is like new.

 

[WillG]

Homelite 330 intake boot fun!! Actually not too bad to get apart. Replacing pulse and fuel lines while it's apart as well.

Sent from my E6910 using Tapatalk

 

[drf256]

 

[tree monkey]

see how it runs on muffler, then build a pipe

 

[tree monkey]

ya might get done sooner if ya turn it on, ya know, rub it in the right place

 

[drf256]

Too noisy. Didn’t want to disrespect Gregg.