What's on your bench?

[redlight066]

 

[Car wash guy]

Putting a new stainless Carlton bar on my 288. Rails are super tight hopefully it wears in.

Sent from my iPhone using Tapatalk

 

[Car wash guy]

I was out of short bars so off to the shop. Thought I would try one of Oregon’s aluminum core bars.

Sent from my iPhone using Tapatalk

 

[Car wash guy]

The shop also had some chain I never seen before. I’ll give it a try today. Dealer says it’s super hard. We shall see

Sent from my iPhone using Tapatalk

 

[RI Chevy]

The Carlton bar is Stainless Steel?
I thought they were just polished steel?

 

[Car wash guy]

You would be correct. Magnet sticks right to it.


Sent from my iPhone using Tapatalk

 

[WillG]

Got the spacers cut at lunch time today. Gonna work perfectly!

Sent from my E6910 using Tapatalk

 

[PA Dan]

I was out of short bars so off to the shop. Thought I would try one of Oregon’s aluminum core bars.

Sent from my iPhone using Tapatalk

How does that saw run?

 

[RI Chevy]

You would be correct. Magnet sticks right to it.


Sent from my iPhone using Tapatalk

I always thought the good stainless was non magnetic?

I researched, and I guess some stainless is magnetic now. [emoji2369] Has more steel in it and less nickel.

 

[Car wash guy]

How does that saw run?

That little saw runs like a raped ape. Got 2 more that’s not ported. They run good too. This one will make you smile while running it.


Sent from my iPhone using Tapatalk

 

[Car wash guy]

Most stainless will not stick to a magnet. Been getting some Chinese hardware that is marked stainless but is not.


Sent from my iPhone using Tapatalk

 

[Car wash guy]

The shop also had some chain I never seen before. I’ll give it a try today. Dealer says it’s super hard. We shall see

Sent from my iPhone using Tapatalk

Well I ran that chain for 2 tanks through the 346. Straight out of the box not sharpened. Little to no stretch. I never tightened it. Not super sharp but as good as you will get outta the box. A little more kick back than I’m used too but might be the saw. Here’s a pic after 2 tanks. I’m gonna touch it up and try it again in a couple days.

Sent from my iPhone using Tapatalk

 

[PA Dan]

That little saw runs like a raped ape. Got 2 more that’s not ported. They run good too. This one will make you smile while running it.


Sent from my iPhone using Tapatalk

I figured that was going to be your answer! I have one he ported also!

 

[Car wash guy]

I’ve got a 55 he ported too. Not as fast but got lots more bottom.


Sent from my iPhone using Tapatalk

 

[PA Dan]

I’ve got a 55 he ported too. Not as fast but got lots more bottom.


Sent from my iPhone using Tapatalk

He did a 361 cylinder and just did a 359 for me! The 346 is something special though!

 

[Car wash guy]

How did the 359 turn out. I’ve got 2 I only run one occasionally. I try to run 24 s on them and depending on the wood they are underpowered.


Sent from my iPhone using Tapatalk

 

[PA Dan]

How did the 359 turn out. I’ve got 2 I only run one occasionally. I try to run 24 s on them and depending on the wood they are underpowered.


Sent from my iPhone using Tapatalk

I haven't picked it up yet but I have run some of his ported 359's. I liked them that's why he did this one!

 

[Homelite750]

Found an air leak that you don't often see.

 

[David Young]

Dang.
I’d epoxy that bad baby.

 

[Car wash guy]

Found an air leak that you don't often see.

Is it cracked?


Sent from my iPhone using Tapatalk