What's on your bench?

[NateSaw]

View attachment 376491

View attachment 376492

So far it's been fuel lines, primer bulbs, a little carburetor work, replacing trimmer lines, a few missing screws, and soldering the wires on an ignition switch. I still need to look into the tiller/cultivator.

Mark

Your shop looks wonderful man!

 

[Johnmn]

Gonna be checking over and listing some saws for a friend. These are the first two.
400 is new never fueled so that one's easy the 044 is a 12mm arctic.

 

[maulhead]

Gonna be checking over and listing some saws for a friend. These are the first two.
400 is new never fueled so that one's easy the 044 is a 12mm arctic. View attachment 376574

What's the price gonna be on the 044, what's wrong with it?

 

[Johnmn]

What's the price gonna be on the 044, what's wrong with it?

Supposedly nothing is wrong but I wanted to check it out first. I'm not 100% sure on prices yet

 

[heimannm]

Anyone familiar with this version of the Walbro WYL carburetor? I am looking for a kit with the correct metering diaphragm. This one has an extra tab with a hole in the metering diaphragm.



The K20-WYL kits all come with the gasket, just not the diaphragm.



The extra hole work with the primer/purge bulb.





Thanks in advance.

Mark

P.S. This carburetor is from the tiller/cultivator by the way.

 

[NateSaw]

Gonna be checking over and listing some saws for a friend. These are the first two.
400 is new never fueled so that one's easy the 044 is a 12mm arctic. View attachment 376574

Price on 044?

 

[Johnmn]

Price on 044?

Not 100% sure, I am going to look it over this weekend to make sure it doesn't need anything.

 

[NateSaw]

What's the price gonna be on the 044, what's wrong with it?

Sorry @maulhead . I jumped without looking.

 

[Johnmn]

I'll let you guys know what I find ASAP I just wanted to see if there was interest.

 

[Partner]

I'm wondering what engine a 16" 60Z circular saw needs and what is the turnover of this saw

 

[Ronie]

Started on a 3 point boom pole/skidder yesterday.

 

[Duce]

Started on a 3 point boom pole/skidder yesterday.

View attachment 376615View attachment 376616

Will make a great wheelie tractor.

 

[Czed]

Rebuilt a 272 the oem carb kept giving me fits
I didn't have a good extra carb so I put a 10.00 am carb on it

It has a narrow range on low-end but tuned in good and has held it
It's a strong saw for a stocker.

 

[Al Smith]

The 455 only needs a carb kit he saysView attachment 376567
It runs but has piston slap
He gave it to me i guess I'll fix it.

Trueth being you never really know what's wrong with them until you investigate .Fact on my latest project I assumed both saws needed coils .One it turned out had an air gap of about 40 thou .Never bothered to check it before hand . However still installed the new coil ,got spark .I think now they had ran the jets out so far in trying to start it floods .I'm about to find out why .

 

[Ronie]

I finished my boom up this afternoon, just need to pick some pant up and spray it.

 

[Czed]

Someone actually wanted a fs44 fixed

 

[Partner]

I finished my boom up this afternoon, just need to pick some

I'm supposed to make a slightly larger jack for a larger tractor, but with a cylinder on the arm

 

[Ronie]

Will make a great wheelie tractor.

I plan on adding a couple of hundred pounds to the front, hopefully that will keep the front end down.

 

[Ronie]

I'm supposed to make a slightly larger jack for a larger tractor, but with a cylinder on the arm

That would be nice to have. When I was looking around for a used boom, I saw one one on FB but the guy wanted $800 for it.

 

[Maintenance Chief]

I finished my boom up this afternoon, just need to pick some pant up and spray it.

Talk about a dream to pull motors with!