What's on your bench?

[heimannm]

Yesterday was this.





Today, these.





I don't think the edger was ever in production as this was rescued from the warehouse when McCulloch was moving to Lake Havasu.

The welder was a relatively short run but as you can see, they made a number of changes along the way. The dirty looking one has the large Tillotson HL, the brighter one has the same carburetor as the BP-1 chainsaw. The dirty looking one does run well though I have not yet attempted to strike an arc with it.

Mark

 

[Mkinslow]

Almost done with this one

@huskihl

Sent from my SM-G892A using Tapatalk

 

[huskihl]

Almost done with this one

@huskihl

Sent from my SM-G892A using Tapatalk

 

[USMC615]

Almost done with this one

@huskihl

Sent from my SM-G892A using Tapatalk

Outstanding!

 

[jacob j.]

Almost done with this one

@huskihl

Sent from my SM-G892A using Tapatalk

Where are you going to engrave the words "Xtra Sausage"?

 

[Mastermind]

Almost done with this one

@huskihl

Sent from my SM-G892A using Tapatalk

That's a nice knife. Ifn I carried a straight blade, I'd be hitting you up for one.....

 

[Mkinslow]

That's a nice knife. Ifn I carried a straight blade, I'd be hitting you up for one.....

Thank you sir, I make smaller ones down to 5 inches, handier than people think.

 

[Mkinslow]

Where are you going to engrave the words "Xtra Sausage"?

Lol,I wish I could do that, would be awesome

 

[Mkinslow]

Outstanding!

Thank you sir!

 

[semicabin]

New project

 

[Mastermind]

View attachment 213484 New project

Very cool.

 

[USMC615]

View attachment 213484 New project

Interesting...

 

[Cut4fun]

Me likey when a new customer = homeowner firewood cutter shows up with this. 2014 husky 390. He said he runs 24" most time and has a 32" too.

I threw my 24" bar and chain on it for test and tune session.

 

[chipper1]

Me likey when a new customer = homeowner firewood cutter shows up with this. 2014 husky 390. He said he runs 24" most time and has a 32" too.

I threw my 24" bar and chain on it for test and tune session.

View attachment 213518 View attachment 213519

Can we get a picture of the startup directions on the back of the cover?
Curious.

 

[Cut4fun]

Can we get a picture of the startup directions on the back of the cover?
Curious.

I seen that. Also had marking to remind him of the decomp.

I think he older then me and retired too. So I can understand.

 

[chipper1]

I seen that. Also had marking to remind him of the decomp.

I think he older then me and retired too. So I can understand.

I've seen it on some of the vent saws, I had a 460 that has some writing on it, can't remember what it said though lol.

 

[WillG]

031 AV I picked up at a swap meet not too long ago. Getting a carb kit, fuel line, spark plug, chain and a clean up. Fired on a shot of mix down the carb. Compression test shows 150 plus psi.

Sent from my E6910 using Tapatalk

 

[dustinwilt68]

Little project I picked up tonight, swapped the spur drive for a rim and the clutch cover from a 572 wrap kit on it so far, piston is pristine though, gonna swap the carb and coil next, this one has the small Zama and 13,300 coil, new starter housing is next, anyone have any leads on a 2065 decal?

 

[David Young]

Little project I picked up tonight, swapped the spur drive for a rim and the clutch cover from a 572 wrap kit on it so far, piston is pristine though, gonna swap the carb and coil next, this one has the small Zama and 13,300 coil, new starter housing is next, anyone have any leads on a 2065 decal?View attachment 213582 View attachment 213583

cover looks sweet!

 

[huskihl]

@Bobby Frank