What's on your bench?

[spencerpaving]

View attachment 171878

I like what's happening in this pic....

 

[shadco]

Don't believe this one had gas in it yet. Yours was just a little quicker stock

I’m guessing you got the label.

Mine probably had a half tank or so thru it in wood, and 5 or 6 heat cycles.

.

 

[huskihl]

I’m guessing you got the label.

Mine probably had a half tank or so thru it in wood, and 5 or 6 heat cycles.

.

Yep. There's a ups drop off a half hour north. Had my daughter take it home with her tonight to drop off in the morning

 

[shadco]

Yep. There's a ups drop off a half hour north. Had my daughter take it home with her tonight to drop off in the morning

Wow, thanks.

.

 

[MG porting]

Well this I something new my friend bought this 200t and it wasn't a runner and funny thing is someone had put a new top end on it not a ton of time on it all the bearings look to fine so ether someone didn't flush out the crankcase or they deliberately tost something down the carb not cool in ether case ive' been swomped with Saw's and helping my little woman out the best I can while her ankle heals but I really wanted to share this 200t saga.

 

[Deets066]

I like what's happening in this pic....

Lot more than a guy would think

 

[tickbitintn]

Well this I something new my friend bought this 200t and it wasn't a runner and funny thing is someone had put a new top end on it not a ton of time on it all the bearings look to fine so ether someone didn't flush out the crankcase or they deliberately tost something down the carb not cool in ether case ive' been swomped with Saw's and helping my little woman out the best I can while her ankle heals but I really wanted to share this 200t saga.View attachment 171898 View attachment 171899 View attachment 171900 View attachment 171901 View attachment 171902

Both pin locaters still there?
Looks to me "dents" are about the size of one.

Sent from my XT1635-01 using Tapatalk

 

[usmcbuckwild]

Both pin locaters still there?
Looks to me "dents" are about the size of one.

Sent from my XT1635-01 using Tapatalk

Looks like a pin is sticking up out of the piston.

 

[Stump Shot]

A two into one deal here, should be interesting....

 

[Onan18]

Pair of 450 X-Torq, guy is insistent that he wants to run 20" 3/8" bars. I set them up with full skip, they're better...

 

[Altamaha]

View attachment 171970
Pair of 450 X-Torq, guy is insistent that he wants to run 20" 3/8" bars. I set them up with full skip, they're better...

I have a 455, 20 inch bar. I run full skip round file chisel. Man does it cut!!! I have a new 24 inch bar for it, thinking about putting it on.

 

[Stump Shot]

 

[Dub11]

A two into one deal here, should be interesting.... View attachment 171965

Dibz on left over Stihl parts.
I here they are worth there weight in gold and *s-word.

 

[MustangMike]

Looks like a pin is sticking up out of the piston.

Or 2!

 

[MustangMike]

I got lots of extra parts for them also, likely everything you don't need! If you have a cylinder that can be cleaned up that you don't need, let me know.

 

[Stump Shot]

Dibz on left over Stihl parts.
I here they are worth there weight in gold and *s-word.

Be lucky if there's anything left over worth its weight in chit when this is done.

 

[Dub11]

Be lucky if there's anything left over worth its weight in chit when this is done.
View attachment 171988

Well then can you knock some dirt off so i dont receive so much *s-word mmmkay thanks by.

 

[Stump Shot]

I got lots of extra parts for them also, likely everything you don't need! If you have a cylinder that can be cleaned up that you don't need, let me know.

More projects in the pipeline here, hard to say what and when will come out of it when it's all done.

 

[Stump Shot]

Well then can you knock some dirt off so i dont receive so much *s-word mmmkay thanks by.

No, no, no, that's the good stuff. Lol

 

[afleetcommand]