tree monkey 661 turning 15k?!?!?

[paragonbuilder]

Why does the tach get a double reading and screw the tach up? Is it doing the same to the plug?

A plug doesn't get a signal. It discharges the energy created when the field collapses.


Sent from my iPhone using Tapatalk

 

[paragonbuilder]

Scott ain't gonna just draw anyone a picture.....he drops breadcrumbs.

I'm good with that! It makes me think!!


Sent from my iPhone using Tapatalk

 

[Keith Gandy]

A plug doesn't get a signal. It discharges the energy created when the field collapses.


Sent from my iPhone using Tapatalk

But like Mike said the plug can still get interference even through waves. Theres a reason they used certain plugs back in the day around electrical/electronic equipment

 

[jmssaws]

There is no secret remember?
Just slap a 69 on there and your good.

That's correct there is no secret,all he did was put a wj69 on it.
There's nothing to figure out.

 

[dall]

port numbers and carb is totally different than what mods are done to put one saw out in front of another

 

[Keith Gandy]

That's correct there is no secret,all he did was put a wj69 on it.
There's nothing to figure out.

Lol!! I bet there is but I dont blame him if he doesnt share

 

[Keith Gandy]

That's correct there is no secret,all he did was put a wj69 on it.
There's nothing to figure out.

If a WJ69 will run a 064/066 out to 15000 why wont it on a 661?

 

[dall]

lol i like how many are fishing lol

 

[Keith Gandy]

lol i like how many are fishing lol

Lol! I believe Ole Monkey is gonna leave us scratchin our ass!!!

 

[Keith Gandy]

I guess the bottomline is if I got a 661 and ported it The Monkey business would be required !!!

 

[Keith Gandy]

lol i like how many are fishing lol

 

[bikemike]

lol i like how many are fishing lol

I like fishing been 2 years but like fishing lol

 

[bikemike]

I guess the bottomline is if I got a 661 and ported it The Monkey business would be required !!!

Kinda. But port work can change power and torque curve. With the right work it may may chit tons of power but may not make it at rev limited range.

 

[jmssaws]

If a WJ69 will run a 064/066 out to 15000 why wont it on a 661?

Because it has a limited coil.
How could all these different people put a wj69 on one and not get a unlimited saw?

I have no doubt it's turning what the tach reads but it's not from just a wj69 like we are told,also if the coil is not limited what difference would a spark plug make?

Put a wj69 on one and screw the high shut and it will still 4 stroke or burble wfo no load,how can that be?

I'm not doubting that it's turning what it is but it's not just from a standard carb.
Everyone has gotten 14k from a carb but over time it will slow back down,go wow does that happen? The only thing left is the coil so how can it slow it down if you have control over the fuel and air?

 

[Magnumitis]

Linkages on the three carbs I tried this morning WJ 48, 69 and Bing 49, throttle linkage and plate bound around half throttle.

I'm moving on to my chain.

 

[Keith Gandy]

Because it has a limited coil.
How could all these different people put a wj69 on one and not get a unlimited saw?

I have no doubt it's turning what the tach reads but it's not from just a wj69 like we are told,also if the coil is not limited what difference would a spark plug make?

Put a wj69 on one and screw the high shut and it will still 4 stroke or burble wfo no load,how can that be?

I'm not doubting that it's turning what it is but it's not just from a standard carb.
Everyone has gotten 14k from a carb but over time it will slow back down,go wow does that happen? The only thing left is the coil so how can it slow it down if you have control over the fuel and air?

I think Scott ask about the plug for a reason but not sure?

 

[Keith Gandy]

Find a resistor plug with a heat range of a ngk7 and u may have the anwser

 

[Adirondackstihl]

Find a resistor plug with a heat range of a ngk7 and u may have the anwser

You mean "NON" resistor plug correct?
BPM7A
WS6F

 

[paragonbuilder]

Non resistor plugs wigged out the dyno electronics.
So maybe it's wigging out tachs, but I can't see them slowing the saw at all


Sent from my iPhone using Tapatalk

 

[Adirondackstihl]

Non resistor plugs wigged out the dyno electronics.
So maybe it's wigging out tachs, but I can't see them slowing the saw at all


Sent from my iPhone using Tapatalk

Exactly