Todays snag

[exSW]

Picked up this little mess this morning. View attachment 234298 View attachment 234299
All of them feel good pulling over

Olympic down front and one of the "good" later Poulans to the left?

 

[Dub11]

What a waste of nice clean paper...

Don't be getting all jelly.

Olympic down front and one of the "good" later Poulans to the left?

Yes it's an Olympyk mayhaps a 252 ? The sticker is pretty warn away. He had it listed as a Husqvarna lol. And a Poulan 3450

 

[exSW]

Don't be getting all jelly.


Yes it's an Olympyk mayhaps a 252 ? The sticker is pretty warn away. He had it listed as a Husqvarna lol. And a Poulan 3450

If the Super 250's a non runner I could use a clutch cover.

 

[Dub11]

If the Super 250's a non runner I could use a clutch cover.

Ok I'll probably be messing with it tomorrow.

 

[countryhog]

Picked up this little mess this morning. View attachment 234298 View attachment 234299
All of them feel good pulling over

Question is - does the oly have spark?

 

[Dub11]

Question is - does the ply have spark?

That crossed mind too. The guy used to cut wood then got a wood pellet stove so hopefully they only need rubber stuff.

 

[countryhog]

That crossed mind too. The guy used to cut wood then got a wood pellet stove so hopefully they only need rubber stuff.

If it does you could have a goodun. If it needs seals that is a different matter. After many years I still haven’t found a AM set that will fit. Last set I got had to come from Italy, not cheap. Went and installed one of the sets, then discovered the case gasket leaked. Not split the case cause then I need a case gasket. Looking for some right now. Keep us updated

 

[Dub11]

If it does you could have a goodun. If it needs seals that is a different matter. After many years I still haven’t found a AM set that will fit. Last set I got had to come from Italy, not cheap. Went and installed one of the sets, then discovered the case gasket leaked. Not split the case cause then I need a case gasket. Looking for some right now. Keep us updated

So the factory seals aren't a standard size?

Where did you find a part number?

 

[countryhog]

So the factory seals aren't a standard size?

Where did you find a part number?

No!
IPL. 3050015AR
Got dimensions but in my computer

 

[dustinwilt68]

Saved this one recently, non decomp is jug, fired right up

 

[Frank bierce]

Got this bad boy from the family farm. It was my grandpa’s. Needs a few parts.View attachment 228100View attachment 228101View attachment 228102View attachment 228103

What parts are you needing?

 

[Dub11]

And now I have the sads

 

[JTV10]

What parts are you needing?

I found all the parts online at at my local dealer. Did a complete tear down and rebuild, the only part that was a pita to get was the bearing with the integrated seal. Still waiting on the clutch cover and carb box cover other than that its all back together.

 

[GCJenks204]

And now I have the sadsView attachment 234474

Can't like that BOOOO

 

[Dub11]

Can't like that BOOOO

If I can't find the parts or it's worse underneath the recoil I'll JB the holes and rough spots and move it to trench duty.

 

[Bigmac]

And now I have the sadsView attachment 234474

Might had a nice fan shroud in storage, if I can find it it’s yours!

 

[Dub11]

Might had a nice fan shroud in storage, if I can find it it’s yours!

Right on!

Saves me from slathering jb everywhere.

 

[Bigmac]

Right on!

Saves me from slathering jb everywhere.

Found it, it dose have the switch in a different location, not sure if it will work for you

 

[Dub11]

Found it, it dose have the switch in a different location, not sure if it will work for youView attachment 234889View attachment 234890View attachment 234891View attachment 234892

If it fits it work lol

 

[redlight066]

I was at the parts counter and Bought this off a landscaper yesterday around 11:00. He got the bad news from the service dept. Bearings were shot. I offered him $100. He said yes waaaayy too fast. Prolly could have got it for less.

Got home and swapped the crankshaft from a donor, and new seals. Carb replaced as well. Had it listed on CL by 2:30. Sold it at 6:00 for $350