The Swap Meet Thread

[GlocknStihl]

Any interest in an ohsixfour case? Crank was shot, and this had a couple epoxy spots on it. Chipped them off to find two holes, each case half, into the oil tank Not sure how holes would have ended up there. Lol
Next issue is a muffler mounting hole. Inserting proper bolt would be the same as throwing a hotdog down a hallway.

Can’t think of anything I need at the moment. Just seeing if anyone would like

It was left sitting on concrete would be my guess?

 

[Frank bierce]

It was left sitting on concrete would be my guess?

No white death. Holes are from some kind of puncture, or they were drilled.

 

[Canadian farm boy]

No white death. Holes are from some kind of puncture, or they were drilled.

Handle bar screws way to long???

 

[maulhead]

No white death. Holes are from some kind of puncture, or they were drilled.

Just a guess, but maybe someone used too long of screws to hold the handle on the saw?

I had 044 case once, someone had put too long of screws in the handle mount and it punctured the case.

 

[Frank bierce]

Handle bar screws way to long???

That would make sense

 

[Frank bierce]

Just a guess, but maybe someone used too long of screws to hold the handle on the saw?

I had 044 case once, someone had put too long of screws in the handle mount and it punctured the case.

Hahaha...look at you guys . Both must have hit post about the same time. Lol

 

[DrewUth]

Picked this 750evl up at a motorcycle swap meet over the weekend, essentially saving it from the scrap heap I believe. Missing the clutch cover and with no B&C, it does have excellent compression. I was told it ran last year but the fuel lines went away. I could get it running, but I'm not really into Echos so I though I'd post it up here. I'm a Poulan guy, anyone have something of similar displacement and condition to trade? I'm not sure what the cash value of it is, I don't see many parts on ebay when I went looking for a clutch cover.

 

[cowroy]

Looking for an 084 top cover. The uglier the better just not broke or burnt.

 

[kfd518]

Looking for a crank bearing clutch side for an 056 super #9523-003-4460.

Also looking for a builder 066,660,661

 

[Homemade]

Looking for an oil pump and worm drive for a 036/034. I have green backs to trade, as my collection of parts are small.

 

[Mastermind]

Handle bar screws way to long???

Bingo

 

[Mastermind]

I've found myself in need of a coil for a 6400 - 7900 Dolmar.

I have stuff to trade, or I can provide worthless government notes.

 

[Mastermind]

I've found myself in need of a coil for a 6400 - 7900 Dolmar.

I have stuff to trade, or I can provide worthless government notes.

Traded some notes.....got me a coil.

This site is AWESOME !!!!

 

[brandonstclair20]

I got a Tillotson HS 228C carburetor for a husqvarna 281, and I would like to trade it for a carburetor for a husqvarna 266.


Sent from my iPhone using Tapatalk

 

[GlocknStihl]

Any of you want to trade me a 16" 325 bar for a 3005 Stihl mount ? I have an 18" 325/063 in 3005. I'd like the 16" for my 241.

 

[winton1982]

Need a good piston and jug for a Stihl ms291.


Sent from my iPhone using Tapatalk

 

[GlocknStihl]

Need a good piston and jug for a Stihl ms291.


Sent from my iPhone using Tapatalk

I can normally handle all your Hyway cylinder needs, but I havent seen any AM for these yet.

 

[usmcbuckwild]

Any of you want to trade me a 16" 325 bar for a 3005 Stihl mount ? I have an 18" 325/063 in 3005. I'd like the 16" for my 241.

I have a couple 16” .325 0.063 bars.

 

[usmcbuckwild]

Looming for an 026 Cyl. Already have a Meteor, just need the cylinder.

 

[GlocknStihl]

I have a couple 16” .325 0.063 bars.

PM me some pictures