The Swap Meet Thread

[psuiewalsh]

@t4driller

 

[t4driller]

353 and 346 should be sane, 345 , 350 are same. Like beaglebriar said they are different on pto side

 

[psuiewalsh]

Looking for an good condition OEM handlebar for an 066 flat top.

 

[Homemade]

Looking for a 288 top cover. Needs factory cover screws still captive and intact. And needs decomp hole. Rough condition is ok as long as it’s functional.

 

[Drptrch]

Looking for a 288 top cover. Needs factory cover screws still captive and intact. And needs decomp hole. Rough condition is ok as long as it’s functional.

[emoji13][emoji13]

Oh, noticed it’s missing captive screws


Erik

 

[Homemade]

No go.



Missing the decomp hole. [emoji41]

 

[Drptrch]

No go.



Missing the decomp hole. [emoji41]

But it’s a Piltz, can run a 100” Bar with that on it


Erik

 

[brandonstclair20]

Husqvarna 51 project saw, trade for nice screw cap 046 tank. Or will sell saw.

Sent from my iPhone using Tapatalk

 

[huskihl]

Looking for a 385/390xp intake boot and a 372 xt tuning grommet

 

[SteveinUT]

Anyone have a WA19A? I need one for a Poulan S25DA project I got for $8...

 

[Sleeper]

Anyone have a WA19A? I need one for a Poulan S25DA project I got for $8...

Tell you what... you pay shipping and I will send a complete parts saw. Not sure what carb it has, but I could check. And to be sure that the saws are the same, I could use a picture of your S25DA so I look at the right one. (some reason I think there were a few different designs of it, but I might be wrong)

 

[SteveinUT]

Tell you what... you pay shipping and I will send a complete parts saw. Not sure what carb it has, but I could check. And to be sure that the saws are the same, I could use a picture of your S25DA so I look at the right one. (some reason I think there were a few different designs of it, but I might be wrong)

Thanks Sleeper! I will take you up on that! I won't be home until Tuesday, so I can't take a pic of mine, but it's the same as this one below. I'll hit you up when I get home and work out the specifics. Thanks again!

 

[Mastermind]

Hey........anyone got a good used MS441 jug?

 

[Sleeper]

Anybody have a scored or bad Poulan 3300 or similar cylinder and piston? Or good one that needs to go for a reasonable price?

I have an idea for a project... it will need some planning and dimension checking... see, I have this mint saw that would be a nice sleeper...

Edit: Forgot to mention that this saw's cylinder/piston is probably scored, hence looking for another one. I am also looking at seeing if there are cylinder/piston kits from other saws that would fit with some minor modifications.

 

[Mastermind]

Hey........anyone got a good used MS441 jug?

This is not needed. Shaun is gonna fix the one I have.

 

[Sleeper]

Anyone have a Poulan 330 carb sitting around? This is for the AdStihl Raffle saw.

Send a pm with price and we'll go from there.

Thanks

 

[Mastermind]

Anyone have a Poulan 330 carb sitting around? This is for the AdStihl Raffle saw.

Send a pm with price and we'll go from there.

Thanks

Sent you a message.

 

[cus_deluxe]

No go.



Missing the decomp hole. [emoji41]

Still need? Low top i assume?

 

[Homemade]

Still need? Low top i assume?

Yeah, my screws are no longer staying captive. And I lost one already.

 

[cus_deluxe]

Ill get u a pic shortly sir.