The Swap Meet Thread

[Wagnerwerks]

Looking for a decent 24" bar (with or without chain loop) for my Homelite 410, doesn't need to be perfect. Have a few project saws to trade or some plain old greenbacks.
Thanks
Jeff

I may have this....

 

[jacob j.]

Hi boys- I'm looking for a PTO side case half for 385...I have lots to trade...

 

[Wagnerwerks]

Hi boys- I'm looking for a PTO side case half for 385...I have lots to trade...

How nice must it be? This one's missing some paint and is worn a little at the one hole shown in the second picture.

 

[jacob j.]

I think that would work just fine for me. I'm building a saw for a logger friend...

 

[Wagnerwerks]

Sounds good. Still live in Oregon?

 

[bulletpruf]

Working on a 038 Magnum. Looking for a new/NOS tank and an NOS piston.

Also have an 020T Super - motor is good, but everything else is beat to he11. Anyone got any exterior bits? If you have a clean one with a bad motor, I'd buy that, too.

Thanks

 

[Matt M.]

I need,
066 metal tag top cover, NOS or as nice as possible. And air filter cover.
Wide clutch cover
Early style tank vent
Would consider buying another nice tank /rear handle. Early style

I have green to trade. This is my toy so I would like to make it as nice as possible. Thanks for any help!

 

[Red97]

24" 3/8 .050 Don't think it was ever used. Tip still smooth. .375 slot. S clip spacer will allow use on smaller studs. Or 4 coils of 5/16×3/8 extension spring on each stud.

Sent from my SM-G950U using Tapatalk

 

[Jon1212]

24" 3/8 .050 Don't think it was ever used. Tip still smooth. .375 slot. S clip spacer will allow use on smaller studs. Or 4 coils of 5/16×3/8 extension spring on each stud.

Sent from my SM-G950U using Tapatalk

That's the bar @jk14 was looking for.

My, that Windsor CJL sure is nice.

 

[Red97]

That's the bar @jk14 was looking for.

My, that Windsor CJL sure is nice.

That's who it was..

I'm going to have a bar cull after the new year.. Going to all stihl mount. Except a couple k095.

Sent from my SM-G950U using Tapatalk

 

[460 magnum]

24" 3/8 .050 Don't think it was ever used. Tip still smooth. .375 slot. S clip spacer will allow use on smaller studs. Or 4 coils of 5/16×3/8 extension spring on each stud.

Nice HOMELITE bar

Sent from my SM-G950U using Tapatalk

 

[Mastermind]

Seeking some 390/385XP parts.

All brake parts including handle, carb box floor, carb, intake boot and associated parts, oil pump drive, clutch and drum, handlebar.

I got the brake parts except for the brake handle, carb box floor, and an OEM half wrap handle if you want it.

Still seeking intake parts, brake handle, clutch and drum, and oil pump drive.

Have cash, or parts to trade.

 

[Frank bierce]

I’m fairly certain I have what you need.

 

[jacob j.]

I’m fairly certain I have what you need.

I have a new aftermarket clutch drum I can throw in his box but I have zero clutches or intake parts.

 

[redlinefever]

ISO clutch and drum for a 394 395 have cash

 

[Mastermind]

I’m fairly certain I have what you need.

Tell me more.......please.

 

[Frank bierce]

Tell me more.......please.

It all started when I took a 385 apart to do a full rebuild. Needless to say, it is still in the bucket I set all the parts in. Lol. If my memory serves me correctly...the clutch was broken, but have the drum...and possibly another clutch somewhere.

 

[mdavlee]

Still seeking intake parts, brake handle, clutch and drum, and oil pump drive.

Have cash, or parts to trade.

Just the boot or elbow too?

 

[jk14]

24" 3/8 .050 Don't think it was ever used. Tip still smooth. .375 slot. S clip spacer will allow use on smaller studs. Or 4 coils of 5/16×3/8 extension spring on each stud.

Sent from my SM-G950U using Tapatalk

Pm inbound

 

[Frank bierce]

Still seeking intake parts, brake handle, clutch and drum, and oil pump drive.

Have cash, or parts to trade.

Also do have these clutches. Bottom one is a 390 top is 385...not sure if there is a difference in them.