The Swap Meet Thread

[brandonstclair20]

Completely rebuilt MS261 for $450 shipped. All oem except the clutch cover and bar nuts. Maybe someone could have it send to @Mastermind to have some work done. No, I will not pay for the porting.

Sent from my iPhone using Tapatalk

 

[Wagnerwerks]

Anyone have a set of 034s or 036 cases they would trade off? I have lots of saws and part to trade. Ty

 

[brushwacker]

I have an 034 s bottom w/ the crank assy. I remember the top end was bad and I stripped the out side parts. Need to double check but I think no breaks or cracks. Not very clean and missing some paint. Haven't been splitting any crank cases so I'd trade it with the crank assy if you're interested.
I also have an early 034 complete engine looks in good condition, has the front chain adjuster. Bought it on ebay several years ago supposed to been a good runner when removed.

 

[decableguy2000]

Looking for a couple of Husqvarna 350 parts, top cover with out the primer, screws for the bearing cap to base, Zama c3 el 17/18, chain brake guts

 

[beaglebriar]

Looking for a couple of Husqvarna 350 parts, top cover with out the primer, screws for the bearing cap to base, Zama c3 el 17/18, chain brake guts

I probably have screws of you still need them.

 

[beaglebriar]

Looking for a couple top cover screws for a Husky 254. Pretty sure 262/257 screws are the same. Cash or maybe parts to trade.

 

[Termitebuffet]

Looking for a couple top cover screws for a Husky 254. Pretty sure 262/257 screws are the same. Cash or maybe parts to trade.

Still need ?

 

[beaglebriar]

Still need ?

Yesh.

 

[Termitebuffet]

Yesh.

I tex bax

 

[ranchdadmike]

Looking for a nicer OE 346 top cover..old style with the clips. Have a few husky parts or $ to trade


Sent from my iPhone using Tapatalk

 

[Onan18]

Looking for a nicer OE 346 top cover..old style with the clips. Have $ to trade


Sent from my iPhone using Tapatalk

They are under $30.00 new.

 

[ranchdadmike]

They are under $30.00 new.

Thank you sir...I just found one, that quick. I was looking for a little 'patina' anyway..the rest of the saw isn't new..I was just looking for no holes or cracks.


Sent from my iPhone using Tapatalk

 

[67L36Driver]

Remington Logmaster parts needed.
Rewind starter or housing.

Air filter cover/retainer.

Tilly HL43 carb.

Last but not least. Remington guide bar #49436. 24" x .077" gauge with or without roller nose.

UPS lost the bar.

[emoji30][emoji30][emoji30][emoji30][emoji30][emoji30][emoji24][emoji24][emoji24]

 

[67L36Driver]

Remington #49436.

3/8" x 20" Stihl shown for comparison.

 

[Wagnerwerks]

I have an 034 s bottom w/ the crank assy. I remember the top end was bad and I stripped the out side parts. Need to double check but I think no breaks or cracks. Not very clean and missing some paint. Haven't been splitting any crank cases so I'd trade it with the crank assy if you're interested.
I also have an early 034 complete engine looks in good condition, has the front chain adjuster. Bought it on ebay several years ago supposed to been a good runner when removed.

Pm scented.

 

[dustinwilt68]

#Dallisback

 

[Dub11]

#Dallisback

Where?

 

[brandonstclair20]

12mm pin Stihl 044 for $350 shipped, any takers?


Sent from my iPhone using Tapatalk

 

[ranchdadmike]

12mm pin Stihl 044 for $350 shipped, any takers?


Sent from my iPhone using Tapatalk

@rattler


Sent from my iPhone using Tapatalk

 

[P.M.P.]

Hi guys Im in need of a coil for one of my main saws Makita 7900 oem or if you have a 272 I will be happy to make it work.

Had the wire brake off yesterday. It was barely hanging on the insulation was cracked through had it liguid taped. I was hard on it taking the plug out before and it finally gave in.