The Swap Meet Thread

[jrsdws]

I have 4 new chains .325" x 0.050" 78dl. I think all are branded Sabre if anybody is interested in them.

Accepted in trade: 3/8" x 0.050" chains......or regrind of about 4 square ground firewood chains.

 

[jrsdws]

Also have a brand new Oregon bar and chain combo. These have never been on a saw. The bar is Husky large mount, 20" 3/8 x 0.058" with 72dl part #208SLHD009. The chain is Oregon #73LGX072 full chisel chain.

I'd be interested in a new or nice condition 18" Husky small mount bar 3/8" x 0.050" OR a decent usable condition 32" Husky large mount bar 3/8" x 0.050".

 

[fearofpavement]

If nobody has called dibs on the 009, I might be interested. I have a rear handled 011 that I need a recoil for.

I have an 011 parts saw. (missing pieces but fires on mix) It doesn't have a carb. Not sure it has a recoil but it probably does since I was able to get it to pop unless I just spun it with my mighty fingers...
(I've parted this saw and sold some of it on eBay. Still have some misc parts and pieces if someone needs bits)

 

[B&BLogging]

Good evening everyone! I'm always looking for blown up 385's or 372's. Or all the plastic that fits em!
Message me if you have anything..
Thanks

 

[Jonesy11]

Looking for rear tank handle for 038 and 52mm mag piston. Mine came with a rigged block of wood and deck screws in it.
Have a runner 290 minus carb and exhaust cover for trade, also have cash.

Sent from my SPH-L710 using Tapatalk

 

[Gunn]

I have an 038 tank. Lemme know if you'd like some pics. I may have a piston (used but serviceable) also.

 

[Jonesy11]

I have an 038 tank. Lemme know if you'd like some pics. I may have a piston (used but serviceable) also.

Pictures would be great. What are you looking to get?

 

[Toad22t]

I'm looking for a 056 magll 56mm piston if someone has one.

 

[mnmforestry]

I've got a 32" gb bar but don't think it's a ti bar. It is stihl mount. It's on a 08s that I got on trade.

 

[Tractorsaw1]

I have a ms460 cylinder & an 044 cylinder, the 044 has a small ding out under the exhaust, it may be scrap. The 460 has a little transfer but would clean up nice. Looking for a 359 or 357 cylinder. Also looking for a 2159 top cover, & of course the 199 carb. Could use a muffler bracket for a 390 & this 2159 project.

 

[Shanks]

Also have a brand new Oregon bar and chain combo. These have never been on a saw. The bar is Husky large mount, 20" 3/8 x 0.058" with 72dl part #208SLHD009. The chain is Oregon #73LGX072 full chisel chain.

I'd be interested in a new or nice condition 18" Husky small mount bar 3/8" x 0.050" OR a decent usable condition 32" Husky large mount bar 3/8" x 0.050".

I've got an 18 .50 k095 like new. PM me your address.

 

[Shanks]

I have a ms460 cylinder & an 044 cylinder, the 044 has a small ding out under the exhaust, it may be scrap. The 460 has a little transfer but would clean up nice. Looking for a 359 or 357 cylinder. Also looking for a 2159 top cover, & of course the 199 carb. Could use a muffler bracket for a 390 & this 2159 project.

 

[Shanks]

I've got a 359 cylinder. I don't know condition offhand. Might have a 199 carb also. PM your address

 

[Jon1212]

Anyone looking for a used, but good condition 395XP half wrap?

I am interested in a 36" 3/8 050, or 063 D009 (large Husqvarna mount bar). I know some of you will wonder WTF am I doing looking for a guide bar.........well a bar of this type wasn't in the 250-300 I picked up at the end of 2014.

 

[Shanks]

I've got a 359 cylinder. I don't know condition offhand. Might have a 199 carb also. PM your address

Boxed up on the way to the post office. Cylinder should clean up. 199 carb and a kit for the carb.

 

[Tractorsaw1]

Awesome, wow, Christmas in January, let me know how I can send reward!

 

[Mastermind]

I need a good 288XP low top cover.......

I have trade fodder.

 

[Shanks]

I've got an 18 .50 k095 like new. PM me your address.

On the way. Will be there monday.

 

[Shanks]

Awesome, wow, Christmas in January, let me know how I can send reward!

Will be there monday.

 

[Shanks]

Looking for a good 272 jug.