The Swap Meet Thread

[Wagnerwerks]

Picked up most of a husky 350 at twisterfest this weekend. Needs air filter stuff, muffler, clutch cover, and I'm sure some other stuff. I have some stihl and husky and $ to trade

I might have a few pieces also....

 

[MG2186]

Picked up most of a husky 350 at twisterfest this weekend. Needs air filter stuff, muffler, clutch cover, and I'm sure some other stuff. I have some stihl and husky and $ to trade

I have all of that stuff, actually it was a complete saw with a toasted cylinder and when i took it a part the bearings were spinning in the crankcase so that was junk too. If you're interested in the rest let me know, it has really nice plastics and covers on it


Sent from my iPhone using Tapatalk

 

[Jon1212]

Anyone have a standard clutch cover for an MS 180? I bought an AM version that doesn't fit(the stud holes are too far apart). This saw was originally set up for the tool less adjuster.

 

[Wagnerwerks]

I have one with a broken catcher piece.....

 

[Jon1212]

I have one with a broken catcher piece.....

That should be fine.

How mush moolahs you be needin' fer it?

Or may haps I have some parts to trade.

 

[Wagnerwerks]

That should be fine.

How mush moolahs you be needin' fer it?

Or may haps I have some parts to trade.

Just shipping. Here's a pic of the carnage... lol

 

[Jon1212]

Just shipping. Here's a pic of the carnage... lol

PM scented message sent.

 

[Definitive Dave]

I might be a total dummy but I was under the impression the bar stud spacing on the toolless 170/180 cases was different and the case had to be swapped to swap covers

 

[Wagnerwerks]

Lol. You may be right, but he should be able to check that in a few days...

 

[Jon1212]

I might be a total dummy but I was under the impression the bar stud spacing on the toolless 170/180 cases was different and the case had to be swapped to swap covers

Lol. You may be right, but he should be able to check that in a few days...

Yeah, I'm fairly certain the one you're sending will work.

Here's the one I ended up with, compared to a spare for my MS 390.

Obviously it won't fit on a MS 180.

 

[Definitive Dave]

Giant turd for a brain I have
Made assumptions based on just plain dumb

 

[Cut4fun]

Anyone have a standard clutch cover for an MS 180? I bought an AM version that doesn't fit(the stud holes are too far apart). This saw was originally set up for the tool less adjuster.

1123 648 0405 from 170 180 018 017 021 025 etc. Check and make sure but what I have saved in a 180 thread.

Filler plate replaced with part 1123 664 2205

T27 filler screw replaced with 1123 664 2400

Quick chain adjust cover replaced with 1123 648 0405

Add the bar adjust from front and done with two new bar nuts.

 

[Mark71gtx]

I need a 260 filter cover. Chinese is fine. Looking for one to be shipped quickly. Does not have to be pretty. PayPal ready, thanks!

 

[Red97]

Looking for husqvarna unlimited /14,100 coil have some $$$ to trade. Possibly some parts.

 

[Armbru84]

Anyone have a wrecked or smoked 660 laying around they would be willing to part with?

 

[skippy]

Looking for husqvarna unlimited /14,100 coil have some $$$ to trade. Possibly some parts.

I think I have not positive . Will check tonight after work

 

[Mastermind]

I have a 066 flat top I would sell, but it's ready to kill trees with.

 

[Armbru84]

I have one of those as well mastermind...perfected by yourself and it kills trees rather nicely. Working on another project.

 

[Jon1212]

Going through some bars tonight, and ran across this.

It's a 24" 063 Windsor Hardnose. "EM" is the mount code, which is the same as the obsolete Oregon D005. The stud slot is 9.5mm. The EM = Electrolux Motors, so it fits Husqvarna large mounts(0.5mm difference), Partner, and Partner based saws, including the PM1000, etc. I modified an EM mount to fit my Olympyk 272F by opening up the stud slot 0.5mm, and enlarging the larger adjuster holes(10 minutes with a dremel, and a carbide burr.

If anyone can actually use this, I'll send it off for the cost of shipping.

 

[Mark71gtx]

@Jon1212 PM sent