The Swap Meet Thread

[Mastermind]

Randy,
Did you find you piston for an 024 yet?

Yep. 9 1/3 finger Ross hooked me up.

 

[big t double]

looking for some ms361 bits....starting with a crankshaft.

 

[dolmarkid]

I'm looking for a complete ms 660 builder project pm me what you have

 

[Jon1212]

Searching for old swedomatic chain brake Assy for husqvarna 288xp. Metal flag type.

@Eccentric

 

[Mark71gtx]

Got what I needed

 

[Tractorsaw1]

Would like to trade 2 346 mufflers for 1 359. I have a cat & non cat. Would take either. Could also use some other 2159/56 parts if any to spare.

 

[MG2186]

Would like to trade 2 346 mufflers for 1 359. I have a cat & non cat. Would take either. Could also use some other 2159/56 parts if any to spare.

I got a nice 2159 cat muffler


Sent from my iPhone using Tapatalk

 

[MG2186]

I've got an old Husky 65L runs good just sitting around if anyone can use it, some nice used 3/8 050 72dl D009 bars, like new Forrester K095 3/8 058 68DL bar. I'm looking for a useable 36" D009 bar/chains, K095 3/8 050 72DL Jonsered lable'd total bar and Jonsered builder saws-630-670,2152,2153,2156,2159

 

[blueberrymuzik]

Looking for a HD air filter cover for a 064. P/N 1122 141 0500

 

[Frank bierce]

Not quite saw related...but a nice addition to a shop...picked these up a few years ago off of a job..customer didn't like the color..these particular ones were never opened. I cracked the box open to take a photo...

6' plug strips x2View attachment 6386

Back home for a little bit...these are still available

 

[Wagnerwerks]

Back home for a little bit...these are still available

What ya looking for? I could use em.

 

[Frank bierce]

What ya looking for? I could use em.

Nothing in particular at this point. Could possibly use a good 24" husky mount bar

 

[Wagnerwerks]

Hmmm... I have a 20, but no 24 in husky. Have a price in mind?

 

[Frank bierce]

Hmmm... I have a 20, but no 24 in husky. Have a price in mind?

Just take care of shipping and they are yours.

 

[Windthrown]

This is now sold. TYVM

I have a good 254 dual prong coil that came off a working saw that will fit several Oly, Mac and Efco saws that I cannot use any more. Its the electronic ignition type. I got it for my dead 245 but the ex had tossed the saw after I moved out and before I could go back and get it. I was a great saw, like an old Fiat Spider: no brakes and all go. $20 clams takes it, shipped USPS in a small flat rate box, anywhere in the US.

 

[GoBigBlue1984]

Needing a coil for a 353 and a top cover clamp for a 353.

 

[Eric Miles]

Looking for plastics for an Efco 962 please let me know if any can be had.

Sent from my SM-N910V using Tapatalk

 

[tickbitintn]

Looking for some jonsered 451e parts. Air filter, and cover. Choke knob / grommet. Front A/V mount.
Have green paper, or possible trade stuff, PP, etc.

Trying to get this going for my brother, will be paying him a surprise visit next month and would like to give it to him then.

 

[jacob j.]

Looking for some jonsered 451e parts. Air filter, and cover. Choke knob / grommet. Front A/V mount.
Have green paper, or possible trade stuff, PP, etc.

Trying to get this going for my brother, will be paying him a surprise visit next month and would like to give it to him then.

Your best bet likely would be to hit up Bplust. That old boy has a lot of Jonsereds stuff. I had three boxes of NOS 49sp/451e/52e/490/590 parts years ago but I gave it all to a Jonsereds collector in Penn.

 

[Windthrown]

I have a set of new and unused Caber rings for a Stihl 034Super/036/MS360/036PRO/MS360PRO that I came across in my saw parts box that I no longer need after selling my 036. These can be great for waking up a tired low compression saw. I prefer them over Stihl OEM rings as they are stiffer. They are also a lot cheaper. 48mm x 1.2mm pair. $12 shipped anywhere in the lower 48.