The Swap Meet Thread

[Ladrhog]

Probably have one of those too. It would be a factory used one

 

[Mastermind]

Excellent.

 

[Ladrhog]

I'll email some pics on thursday

 

[Genius]

I may have a 024 piston too Randy



Dang it, I still gotta look closer at those 009 recoils for you.

 

[SteveSS]

Looking for a throttle rod , interlock and muffler front for a Stihl 026/024.
Also need a clutch cover.

I have a few 1121 parts left over to trade.
I have Brake band and brake handle. Ugly but usable recoil assy. Maybe some other bits.
I have an 020T p&c that should clean up.
And a 362 Stihl cylinder that is iffy has lots of transfer and a chip out of exhaust.
also a few parts off husqvarna 257


Sent from my iPhone using Tapatalk

Did you end up getting any of this stuff? I have a throttle rod, but none of the other stuff at the moment. If you want it, let me know.

 

[Tpagel]

Did you end up getting any of this stuff? I have a throttle rod, but none of the other stuff at the moment. If you want it, let me know.

I am still looking, thanks for the response, I am going to let my dealer price it for me. I can PM you if the price breaks the bank
Thanks
Travis

Got them from Dealer thanks for the offers

 

[Welder56]

Cleaned up this cylinder today. It's a 056 super (54mm) cylinder.

You'll see in the pics below the exhaust port there's some tiny marks?? They were there before I shined er up

I'd take 024S, 026, 034S, or 036 cylinder as a trade if anybody is interested

 

[trooney]

I know I'm going out on a limb, but I'm looking for an 084 full wrap handle, got some 084, 064, 066, 026, 036 and some other parts we can possibly trade. If you can help me out, I'll try to help you out! Thanks.

 

[super3]

Need a 346 crank.

 

[drf256]

I could use an 036 jug or 2. Need one to port for a buddy.

Any 44.7 ms260 cylinders would be welcomed as well.

Would swap parts or labor. Whatever the owner prefers.

 

[Redfin]

Still looking for some 2186 parts.

 

[super3]

Need a 346 crank.

Found one.

 

[Mark71gtx]

Anyone have a cheap solid state coil (blue module) for a Homelite Super XL? I may be interested in two... Thanks!
(Edit) I baked the coil in the oven and it works again!

 

[Mastermind]

Who needed the Husky 55 clutch cover and brake?

I found one.

 

[jacob j.]

Who needed the Husky 55 clutch cover and brake?

I found one.

Nathan Stueve was looking for a couple- I sent him one but I think he needs one more.

 

[KZ1000]

Does anyone out there have a fuel line for a Stihl 020avp 1114 358 7700, thanks.

 

[Mark71gtx]

Handled, thanks @Stihlbro !

 

[Stihlbro]

Anyone have a decent air filter and outer cover for a MS290? I picked up one today without a cover and the filter is roached. Epay has a new one for $20, but I would rather have a used one so the faded plastics match. Thanks!

I very likely have one.

 

[Mark71gtx]

Cool, just let me know when you get a chance to check. Include shipping to 27526 in the price if you don't mind.

 

[Stihlbro]

I could use an 036 jug or 2. Need one to port for a buddy.

Any 44.7 ms260 cylinders would be welcomed as well.

Would swap parts or labor. Whatever the owner prefers.

Mailed.

Handled, thanks @Stihlbro !

Mailed, just pay it forward.