The Swap Meet Thread

[stihl_head1982]

Seems strange to me. It's not like the forum is getting"a cut" or fee...
If it starts here why not keep it here?

Sent from my XT1635-01 using Tapatalk

Totally agreed. May want to be careful.

 

[Bodell0]

Any NOS 064/066 parts out there? Have tons of parts or saws for trade.


Sent from my iPhone using Tapatalk

 

[davidwyby]

I need a 61 or 266xp top cover. Or a Jred that will fit, 630?

 

[Tim N]

Looking to convert my 288xp to high top. Looking for all the parts. I have greenbacks mostly to trade

 

[Ronie]

I need a 61 or 266xp top cover. Or a Jred that will fit, 630?

The older two piece coil 630 should fit and looks better in my opinion. You can can also fit the newer style covers on it if you don't mind drilling and taping new holes on the starter side, you'll also need to shorten it a little in the front. The first pic is a 630 cove and the last two are the newer style cover.

 

[davidwyby]

I like the lower top look like the orange saw on the right. Where the rear of the top matches the height and angle of the handle.

 

[davidwyby]

I think I’m gonna get a top from “nothing but chainsaws” on Instagram

 

[tickbitintn]

Dug out an older project.
038 mag II
Need outer ring around intake boot and out minus the carb.
If it's missing from the picture, I need it!
Presence lever spring needed also.

Have PP, venmo or printed goobermint papers.

Sent from my XT1635-01 using Tapatalk

 

[davidwyby]

I think my local small engine guy has an 038 in the junk pile, you want me to go see?

 

[tickbitintn]

I think my local small engine guy has an 038 in the junk pile, you want me to go see?

Sure, when you can, don't make a special trip.
This has been on the back burner for a while so no rush.

Sent from my XT1635-01 using Tapatalk

 

[davidwyby]

Sure, when you can, don't make a special trip.
This has been on the back burner for a while so no rush.

Sent from my XT1635-01 using Tapatalk

found the pics. I dunno nuttin bout steels.

 

[PogoInTheWoods]

I dunno nuttin bout steels.

Lots o' good parts left on that one.

 

[stihl_head1982]

found the pics. I dunno nuttin bout steels.

Not a bad looking 038.
Should have some stuff left that is usable.

 

[broadwayline]

Looking for a Husky 242

 

[cuinrearview]

I'm looking for a couple loops of .325. .063 gague 81 drivers. Thanks.

 

[cuinrearview]

I forgot, I could use the same numbers in a Stihl mount 18" bar. All of these are going to a friend that wrecked the tip on his 18" laminated bar. I just don't have much around for Stihl other than the bar for the above.

 

[ErnieG]

WTB Jonsereds 930 , 2094 or 95
Would like a complete working saw with good compression .
Please let me know if you may have one to sell .
Thanks
Ernie

 

[cuinrearview]

WTB Jonsereds 930 , 2094 or 95
Would like a complete working saw with good compression .
Please let me know if you may have one to sell .
Thanks
Ernie

@blackbruin

 

[ErnieG]

@blackbruin

I've spoken to him already ...I was a few weeks to late .
Ernie

 

[hoskvarna]

WTB Jonsereds 930 , 2094 or 95
Would like a complete working saw with good compression .
Please let me know if you may have one to sell .
Thanks
Ernie

I have a 910 for sale if interested


Sent from Hoskey hilltop