DOLMAR/MAKITA The Official Sachs Dolmar Dolmar Makita Dolmar Chainsaws Thread

[oddsaws]

Got a nice condition Sachs-Dolmar 114 that I’d like to refresh. I can already see finding parts is challenging. Fortunately most of the parts are in good shape sans a few foam pieces.

Is there any fuel line mods or other part numbers that would work on this series (112/114/117/120)? I was looking at the possibly using a line from a PS-341 but can’t verify the grommet dimension. Hole on the 114 tank is about 13mm.

 

[Partner]

@stary_pan_henry
Ask this man

Got a nice condition Sachs-Dolmar 114 that I’d like to refresh. I can already see finding parts is challenging. Fortunately most of the parts are in good shape sans a few foam pieces.

Is there any fuel line mods or other part numbers that would work on this series (112/114/117/120)? I was looking at the possibly using a line from a PS-341 but can’t verify the grommet dimension. Hole on the 114 tank is about 13mm.

@stary_pan_henry
Ask this man

 

[Shane¹]

Got a nice condition Sachs-Dolmar 114 that I’d like to refresh. I can already see finding parts is challenging. Fortunately most of the parts are in good shape sans a few foam pieces.

Is there any fuel line mods or other part numbers that would work on this series (112/114/117/120)? I was looking at the possibly using a line from a PS-341 but can’t verify the grommet dimension. Hole on the 114 tank is about 13mm.

You need one of these then it is just regular fuel line

 

[oddsaws]

You need one of these then it is just regular fuel line View attachment 475333

Yes sir the one I have on the saw has shrunken and doesn’t fit the hole snug. I thought about putting an o-ring on it.

Haven’t come across one in my online searches so far.

Also had the idea of using a 2 hole rubber grommet if I could find the size

 

[Shane¹]

Yes sir the one I have on the saw has shrunken and doesn’t fit the hole snug. I thought about putting an o-ring on it.

Haven’t come across one in my online searches so far.

Also had the idea of using a 2 hole rubber grommet if I could find the size

You could wrap a piece of Teflon tape around it I have done that on fuel lines before. I have also put a dab of super glue on them before. I probably have some of those let me look and see if I have one that is better.

 

[Shane¹]

@oddsaws is your tank metal or plastic?

 

[oddsaws]

@oddsaws is your tank metal or plastic?

It’s metal

 

[oddsaws]

Going to take a chance on this one https://chainsawr.com/products/dolmar-chainsaw-valve-fitting-965-451-520-new-d-20

The parts list I have has part number 965 451 621

 

[Shane¹]

That definitely looks like it to me

 

[Hulsty]

.

 

[oddsaws]

Anyone know where I could source a 114 air filter or suggest a DIY idea?

Few on eBay but premium prices + duty doesn’t sound good

 

[Shane¹]

Anyone know where I could source a 114 air filter or suggest a DIY idea?

Few on eBay but premium prices + duty doesn’t sound good

I have quite a few older dolmar parts I will check for you. Anything else you need for this 114?

 

[oddsaws]

I have quite a few older dolmar parts I will check for you. Anything else you need for this 114?

I’ll think I may have everything covered for now unless I break something. Will need a few gaskets around the carb and muffler

The saw fired with a shot of gas but sputtered out. Haven’t confirmed if ignition is good.

I would like to get a brake/cover eventually, this one is missing the brake band, not sure what else until I clean it up.

 

[Shane¹]

I’ll think I may have everything covered for now unless I break something. Will need a few gaskets around the carb and muffler

The saw fired with a shot of gas but sputtered out. Haven’t confirmed if ignition is good.

I would like to get a brake/cover eventually, this one is missing the brake band, not sure what else until I clean it up.

View attachment 475632
View attachment 475633

Good thing is you can get the 120si style 1 piece ignitions that work perfect can even get rid of the junk under the flywheel. There is even aftermarket ones now. Brake bands can be found aftermarket now too without the lever but looks like it is still there. Can't believe there is no clutch covers on eBay at all though

 

[FergusonTO35]

A guy named Tor Halle on the FB Dolmar chainsaws group is wanting to sell his NOS never fueled or started Sachs-Dolmar 115:

Log into Facebook

Log into Facebook to start sharing and connecting with your friends, family, and people you know.

www.facebook.com

 

[ErnieG]

What bar mount is the ea6100p ?
I'm having trouble with the oil hole on the E-00153 E8 bar being higher then the oil port on the saw.
I also read that a D009 mount should work on these saws but the adjuster doesn't line up with the hole on the bar.

Thanks very much
Ernie

 

[Wilhelm]

What bar mount is the ea6100p ?
I'm having trouble with the oil hole on a d009 and the E-00153 E8 bars being higher then the oil port on the saw .
According to research either of these bars should work .

Thanks very much
Ernie

EA6100/PS-6100 is small Husqvarna mount, aka k095.

Large mount Husqvarna, aka D009 won't work on them!

 

[ErnieG]

EA6100/PS-6100 is small Husqvarna mount, aka k095.

Large mount Husqvarna, aka D009 won't work on them!

Well that would explain it

Thank you!
Ernie

 

[Wilhelm]

D009 on top, k095 on the bottom.
Clear difference in oiler hole positioning.


Also, D009 is 9mm slot.

Bar Mount Pattern: 17

While k095 is 8.2mm.

Bar Mount Pattern: 01