So what did you buy today

[HumBurner]

Everyone should…at the beginning.

Aye. Never too late, though.

 

[TheDarkLordChinChin]

Bought this on Monday. Very good job, will nearly lift the tarmac off the road.

 

[Partner]

The paper is for an angle grinder, about $10 in total

 

[justoldsaws]

Seafood for 2

 

[Squareground3691]

Been wanting one of these, extended 3/8

 

[Partner]

Riddle for today what is it?

 

[Partner]

I spent about $20, link to the most expensive items below

Szczypce do cięcia szkła nr kat. 700.0

Szczypce do Tiffany nr kat. 700.0 szczególnie przydatne przy pracy ze szkłami artystycznymi (witraże, tiffany etc.), szkło jest rozłamywane...

glass24.pl

Buy Ręczny docisk szczypcowy | 493801 | Essentra Components

Ręczny docisk szczypcowy 493801 na Essentra Components . Na stanie – dostępne z dostawą następnego dnia. Zamów darmową próbkę już dziś. Pobierz pliki 3D CAD

www.essentracomponents.com

3pcs

 

[nbbt]

I wonder what this could be planning on getting mated to???

 

[Squareground3691]

I wonder what this could be planning on getting mated to???

View attachment 393356

I wonder what this could be planning on getting mated to???

View attachment 393356

572xp ported

 

[nbbt]

That would be nice if it had the heated option...

572xp ported

 

[Squareground3691]

That would be nice if it had the heated option...

572XPG on sale here HS Supply ,

 

[Partner]

Sander for $10, I wonder if it's Makita or Bosch The M10 spindle is smaller and the nuts do not fit a standard wrench. There is also no spindle lock button and a switch you will never see again. I'll keep disassembling it, maybe I'll find something about the manufacturer. Someone overdid the grease in the gear because it reached all the way to the rotor stator, see the felt under the small gear wheel and the spindle bearing which is removed outside. Square brushes 6mm Without wires

 

[heimannm]

 

[nbbt]

View attachment 393619

Mark, I wish my wife was as understanding as yours. However she may be close, as she had not yet OK'ed building a building for a respiratory for the items I might acquire. Carry on....

 

[legdelimber]

I think the museum is awesome! I have admiration for the labor of love that it takes to pull this stuff together.
Always kills me a little bit to see those Aumann auctions on the rodeo channel when someones collection is going under the hammer.

But I still wanna know, who gets to shovel the snow out of the gap between the buildings?
The Museum and the next building, that is.

 

[heimannm]

I let it accumulate for added insulation...

 

[deye223]

Got these the other week .

 

[WI_Hedgehog]

Riddle for today what is it?

Stained glass window making tools, if I were to guess.

 

[Partner]

Stained glass window making tools, if I were to guess.

It was about the red syringe / You'd have to ask on the technical gases forum

 

[quattro.pilot]

359 at auction yesterday. Got it cheap enough that I can fix or replace any or all of the usual minor/major suspects and still be much much less than a used craigslist saw, plus I have a good collection of spare parts for 357/359 . Auction didn't want me taking the thing apart pre-sale so when I got home pulled the muffler and piston has a fairly minor "blemish" but I'll replace it anyway just cause it's cheap and at this time I don't think the cylinder has suffered much....would hate to trash a jug simply because I'm foolish/ignorant and don't wanna spend $30.