So what did you buy today

[nbbt]

Picked this up yesterday at horror freight.....

Back when I was a kid you had to make yer own outta lots of pieces.
View attachment 400151

I went with this setup about 2 years ago. Works good. You can use regular cylinders, but without the vent to purge gas while filling ya don't get a complete fill.

 

[Partner]

You shouldn't fill the cylinder completely

 

[slackinoff]

You shouldn't fill the cylinder completely

These aren't a regular disposable 1lb cylinder. You can get a full 1lb fill on these. They are designed for it - "Flame King refillable propane tanks are the only 1lb tanks Certified by the DOT as legally and lawfully refillable and transportable."

 

[Partner]

These aren't a regular disposable 1lb cylinder. You can get a full 1lb fill on these. They are designed for it - "Flame King refillable propane tanks are the only 1lb tanks Certified by the DOT as legally and lawfully refillable and transportable."

We fill gas by weight, leaving some space in the tank here at my place in Europe

 

[slackinoff]

 

[slackinoff]

We fill gas by weight

Cool?......but you are missing the point - this product allows you to FULLY fill their refillable tanks because they have a built in dip tube and vapor valve. When we say FULLY filled - we meant 80% of tank volume. Which is the legal limit full fill amount for any LP tank 1lb, 5lb, 20lb, ect. Disposable or not.

It's hard to safely fully fill (80%) the disposable 1lb tanks, and not to mention illegal to transport.

 

[Partner]

A lot of people fill too much and still make videos on YT

 

[Boomer2230]

You shouldn't fill the cylinder completely

There is a process for a person to be able to fill over the recommended 80%, but you need to not have the propane boiling when filling.

 

[Absolution]

Something I DIDN’T buy today (or ever?). But they are all over Amazon for $13 to $20!

Drill-powered Chainsaws!

View attachment 398336

Philbert

 

[Partner]

Let me also test the tin snips

 

[nbbt]

Guess I should have said good fill not FULL. Yes those flame king cylinders have an fill/overfull port. When you have that vent screw open ya stop filling liquid when it starts to spit liquids. Close the valve with the allen screw and your about RTU.I may have skipped a couple of steps , so don't get to nit-picky technical . . . jsns

 

[Sawdust Man]

This....

 

[Woodslasher]

I visited a fellow saw nut on Saturday morning and picked up a few trinkets:

 

[Partner]

Ten....View attachment 400347

How much I also found 6 gallons and 60

 

[rogue60]

Picked up this old heavy duty looking Oregon breaker and spinner up at a garage sale for $10 is soild can't fault it should clean up good as new

 

[SimonHS]

Picked up this old heavy duty looking Oregon breaker and spinner up at a garage sale for $10 is soild can't fault it should clean up good as new

View attachment 400429View attachment 400430

From memory these anvils are a different length to the modern ones, and difficult to find. You can cut the modern ones down to make them fit though.



Edit: I just found a place that still sells them. Not cheap though.

26890 - "C" ANVIL 3/8 LOW PROFILE 1/4 AND .325 PITCH - OLD - OREGON Authentic Part

Buy an OREGON "C" ANVIL 3/8 LOW PROF 1/4 AND .325 PITCH - OLD part number 545720. We distribute OREGON authentic replacement parts at wholeseller pricing.

www.smallenginesprodealer.com

26889 - "A" ANVIL 3/8 AND .404 PITCH - OLD SPINNER - OREGON Authentic Part

Buy an OREGON "A" ANVIL 3/8 AND .404 PITCH - OLD SPINNER part number 38597. We distribute OREGON authentic replacement parts at wholeseller pricing.

www.smallenginesprodealer.com

 

[rogue60]

From memory these anvils are a different length to the modern ones, and difficult to find. You can cut the modern ones down to make them fit though.

View attachment 400447

Edit: I just found a place that still sells them. Not cheap though.

26890 - "C" ANVIL 3/8 LOW PROFILE 1/4 AND .325 PITCH - OLD - OREGON Authentic Part

Buy an OREGON "C" ANVIL 3/8 LOW PROF 1/4 AND .325 PITCH - OLD part number 545720. We distribute OREGON authentic replacement parts at wholeseller pricing.

www.smallenginesprodealer.com

26889 - "A" ANVIL 3/8 AND .404 PITCH - OLD SPINNER - OREGON Authentic Part

Buy an OREGON "A" ANVIL 3/8 AND .404 PITCH - OLD SPINNER part number 38597. We distribute OREGON authentic replacement parts at wholeseller pricing.

www.smallenginesprodealer.com

Awesome thanks for the info

 

[49erRider]

Got me a 572xp today!

 

[Woodslasher]

It wasn't today, but I picked up 20-30 K&N oil filters on clearance for $3-5 apiece, and two air filters for the Dodge for ~$25 apiece. I also bought a Maxflow for the 500i since I don't like the HD2 setups and picked up a filter cage for 660 #2. I'm really diggin Maxflow's new option where you can pick 1 green 1 white, 2 white, or 2 green elements for your kit.

 

[Absolution]

It wasn't today, but I picked up 20-30 K&N oil filters on clearance for $3-5 apiece, and two air filters for the Dodge for ~$25 apiece. I also bought a Maxflow for the 500i since I don't like the HD2 setups and picked up a filter cage for 660 #2. I'm really diggin Maxflow's new option where you can pick 1 green 1 white, 2 white, or 2 green elements for your kit.
View attachment 400851View attachment 400855View attachment 400852View attachment 400853View attachment 400854

They are defiantly worth it, I used the HD2 on it for a while and I was constantly banging it out or throwing in another one.

This one got a little extra nasty a couple weeks ago.