Simington / Silvey Square Chain Grinders Tips/Tricks/Secrets

[Frank bierce]

 

[chipper1]

View attachment 210890

Good stuff there, I'd like to try one.
Any chance you have the info on how to do them on a silvey hdg-6 raker grinder. I have the attachment and would like to figure it out.

 

[Skeans1]

Good stuff there, I'd like to try one.
Any chance you have the info on how to do them on a silvey hdg-6 raker grinder. I have the attachment and would like to figure it out.

http://www.madsens1.com/sil_hdg6_instruct.htm


Sent from my iPhone using Tapatalk

 

[chipper1]

http://www.madsens1.com/sil_hdg6_instruct.htm


Sent from my iPhone using Tapatalk

Whoops, I meant the gullets, got that part down already.
I've tracked down a couple guys who have talked about the gullet attachment, but have never seen one used.
Just use the super jolly for mine.

 

[Duane(Pa)]

View attachment 210890

@srcarr52 could you copy something like this?

 

[srcarr52]

@srcarr52 could you copy something like this?

Yes I could.

 

[Black Dog Chainsaw]

@srcarr52 could you copy something like this?

I’m working on getting a HDG-6 to Shaun for reproduction. Should be quicker and less wear on the more expensive Silvey/Simington wheels.

 

[moparnut88]

I’m working on getting a HDG-6 to Shaun for reproduction. Should be quicker and less wear on the more expensive Silvey/Simington wheels.

I’d love to have one of those to go with my square grinder.


Sent from my iPhone using Tapatalk

 

[Black Dog Chainsaw]

I’d love to have one of those to go with my square grinder.


Sent from my iPhone using Tapatalk

I’m still working out details on getting the grinder to Iowa, but yes many people have expressed interest in owning one... we’ll see what reproduction costs will be after we get a few working models.

 

[Frank bierce]

I’ve been slowly trying to come up with a high quality “all in one” design. Would likely have two motors. Square grind, raker, and gullet. With a second motor, or possibly a single motor, with a coupler to engage another wheel, could have the ability for round ground as well.
Kind of a pipe dream at the moment. But have scribbled a few ideas on paper.

 

[srcarr52]

I’ve been slowly trying to come up with a high quality “all in one” design. Would likely have two motors. Square grind, raker, and gullet. With a second motor, or possibly a single motor, with a coupler to engage another wheel, could have the ability for round ground as well.
Kind of a pipe dream at the moment. But have scribbled a few ideas on paper.

Like the Stihl USG with square grinding dressers and a quick coupler for a second stone?

 

[Frank bierce]

Like the Stihl USG with square grinding dressers and a quick coupler for a second stone?

more like a rs2/swingarm, with a long shaft that has the capability of uncoupling the main grinder wheel, to couple a secondary wheel below. A hydraulic/pneumatic assist stand...like an office chair, to raise and lower to an acceptable height.
Getting the lower wheel setup for multiple adjustments has been a challenge.

 

[Moparmyway]

New work grind, RS 404

 

[RI Chevy]

Nice Kevin. I dig it...

 

[Duane(Pa)]

 

[RI Chevy]

Nice D Wayne. It will cut...[emoji16]

 

[Duane(Pa)]

Converted this (carefully) with blue wheel

 

[Frank bierce]

https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.com/ulk/itm/324020683646

 

[mdavlee]

https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.com/ulk/itm/324020683646
View attachment 214208

That’s an old one but I’d use it.

 

[chiselbit]

Whoops, I meant the gullets, got that part down already.
I've tracked down a couple guys who have talked about the gullet attachment, but have never seen one used.
Just use the super jolly for mine.

I freehand the gullets with my simington