Show off your muffler mods

[Moparmyway]

And the in between .......

 

[Derf]

I appreciate that you split the muffler open to show us inside. Wish Husky just made it easier to do, like the old 2-series muffs.

 

[huskyboy]

I appreciate that you split the muffler open to show us inside. Wish Husky just made it easier to do, like the old 2-series muffs.

The newer 572 muffler is wayyyyyyy easier than the 562/550 muffler. Took me like 15 minutes. Screen was put back in.

There’s only a small gain in speed, but the torque gain is noticeable by feel. Didn’t get much louder either, just changed the tone a bit.

 

[Moparmyway]

There’s only a small gain in speed, but the torque gain is noticeable by feel. Didn’t get much louder either, just changed the tone a bit.

WAIT .........
Are you sure that you OPENED up the muffler AND you GAINED torque ???

 

[redlight066]

1/4” holes are where it’s at.....

 

[RI Chevy]

If you feel Adventurous, you can go with the 3/8...

 

[huskyboy]

WAIT .........
Are you sure that you OPENED up the muffler AND you GAINED torque ???

I know right!

 

[Czed]

Used a red97 deflector on this 266and one of djs on this 5.00 china jobby for a 372
I need to get smaller screen.

 

[Carhartt]

Nah, that screen will keep the mink out of the chicken coop.

 

[MG porting]

Ahhhhhhh muffler modding just got a lot easier for me now. no more flipping propane torch.

 

[JohnnyBlade]

Nah, that screen will keep the mink out of the chicken coop.

I cant stop laughing at this

 

[PA Dan]

Ahhhhhhh muffler modding just got a lot easier for me now.View attachment 197116 no more flipping propane torch.

That's awesome! I just bought a setup also! Mine might be 30 or 40 years older than yours though!

 

[huskyboy]

7900 muffler that was already gutted got another port courtesy of @SOS Ridgerider. Rivet nuts and screws hold on the deflector and screened.

 

[RI Chevy]

Did you go with the two 1/4" holes, or go bold with two 3/8" holes?

 

[huskyboy]

Did you go with the two 1/4" holes, or go bold with two 3/8" holes?

Very bold

 

[huskyboy]

It already ran good but the second port really made my portwork to the cylinder come alive imo.

 

[MG porting]

That's awesome! I just bought a setup also! Mine might be 30 or 40 years older than yours though!

Lol. That just means yours might last longer. But anyways I need to get the tanks fiuld before I can start messing with it it's not going to be cheap even for the small tanks are around $40 to fill but it will be worth it I don't think I'll empty them to quick. Lol

 

[PA Dan]

Lol. That just means yours might last longer. But anyways I need to get the tanks fiuld before I can start messing with it it's not going to be cheap even for the small tanks are around $40 to fill but it will be worth it I don't think I'll empty them to quick. Lol

Maybe! I went after mine because it had a brazing tip also! My tanks are tall and I was quoted $28 for the oxy bottle.

 

[MG porting]

Maybe! I went after mine because it had a brazing tip also! My tanks are tall and I was quoted $28 for the oxy bottle.

There's only one place here in town that can get my thanks fiuld or exchange there pricey but at the same time I'm not driving out of town spending money for fuel in my truck so it's a trade off. Lol

 

[Deets066]

Lol. That just means yours might last longer. But anyways I need to get the tanks fiuld before I can start messing with it it's not going to be cheap even for the small tanks are around $40 to fill but it will be worth it I don't think I'll empty them to quick. Lol

You’d be surprised, those baby oxy tanks don’t last long