Wiseco Pistons from CCC Racing

[Stump Shot]

Show us your CCC Racing Wiseco Piston and tell us a little about your build, be it a racer, milling or work saw
I'll start out with the one that I just received for an 084 resto-mod work saw project that is in the works with lots of new and NOS parts, metal refinishing and a woods ported. My thoughts are that the lighter piston will allow it to run harder longer, well at least that is the theory anyway...

 

[farminkarman]

Does anyone know if CCandRP offer replacement 1mm NPR rings for the pistons that use them vs. the Cabers?

 

[srcarr52]

Does anyone know if CCandRP offer replacement 1mm NPR rings for the pistons that use them vs. the Cabers?

There are almost no non chrome ring options in the 1mm thickness.

Replacement chrome rings can be ordered directly from Wiseco.

https://www.wiseco.com/product-category/powersports/pistons-powersports/piston-components/ring-set/

 

[farminkarman]

There are almost no non chrome ring options in the 1mm thickness.

Replacement chrome rings can be ordered directly from Wiseco.

https://www.wiseco.com/product-category/powersports/pistons-powersports/piston-components/ring-set/

Thanks Shaun!

 

[jacob j.]

Does anyone know if CCandRP offer replacement 1mm NPR rings for the pistons that use them vs. the Cabers?

I think Dave did have a custom run of 1mm non-chromed rings made but they sold out fast. I was hoping to get a 52mm set for a 460 Wiseco piston I have but wasn't fast enough.

 

[farminkarman]

I think Dave did have a custom run of 1mm non-chromed rings made but they sold out fast. I was hoping to get a 52mm set for a 460 Wiseco piston I have but wasn't fast enough.

I was thinking a non-chrome 52mm ring would be handy for 372 52mm chrome bore cylinders as well.

 

[farminkarman]

I think Dave did have a custom run of 1mm non-chromed rings made but they sold out fast. I was hoping to get a 52mm set for a 460 Wiseco piston I have but wasn't fast enough.

I have a 52mm Wiseco piston for the 046/460 that is setup for the 1.2mm Caber. I bought it to use on a hybrid build but didn't end up using it. Let me know if you want it.

 

[Jake Dykstra]

I'm a little further away the Stump so mine is still in transit. But very hopeful it may make it this week.
My project is an old 044 with a 54mm top end for a 5cube racer. Been slowly working to make it a little faster. The ccc piston will allow for some nice finger ports. After that I'm planning on a big carb upgrade. Stihl 084 or 3120 carb.

 

[Catfishclark89]

My CCC single ring pop-up for my 461. Randy built the saw around the piston. Had more room being a single ring. This is a spicy worksaw. I can tune it upwards of 15k to play around at the gtg’s and fatten it up and cut timber with it. It’s done both. Runs great!

 

[Duane(Pa)]

 

[Bjorn]

Hello. Can Anyone pleace explane what have happened to Dave? I have buy many things from him in the past. But now he have disapered. I livet in Sweden so ebay or hes ccc racing page is all I can order from. I still want to be able to bye part I need. Even I live in Sweden.

 

[EFSM]

Hello. Can Anyone pleace explane what have happened to Dave? I have buy many things from him in the past. But now he have disapered. I livet in Sweden so ebay or hes ccc racing page is all I can order from. I still want to be able to bye part I need. Even I live in Sweden.

https://opeforum.com/threads/definitive-dave-discussion.33616/

 

[Definitive Dave]

the oddball rings are not normally shown/available as anyone can see the page and new guys often buy stuff that is totally not what they need or even anything they can use, I don't have the same time, concentration and patience I used to in regards to helping guys out with more difficult or complex cases, I'll still try but I am SLOWWWWW, expect answers in weeks not hours, I have stopped taking out of USA orders because of a few bad eggs, I won't name anyone specifically but its just dumb